亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

constant speed cylinder Sold to Poland

Release time:2023-11-23 08:22:27 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,constant speed cylinder manufacturer,constant speed cylinder

Poland constant speed cylinder

(Poland constant speed cylinder,produced by Hengyu Group)

constant speed cylinder are widely used in Poland,because of simple structure and reliable operation,excellent temperature resistance,clever hydraulic energy conversion.So our company has designed constant speed cylinder for customers from Poland.

Introduction to constant speed cylinder:

constant speed cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the constant speed cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Factors that should be considered when selecting the oil seal in the constant speed cylinder: some specific factors should be taken into account when selecting the oil seal in the constant speed cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: constant speed cylinder diameter, piston rod diameter, piston rod and piston groove size, constant speed cylinder working pressure, constant speed cylinder movement speed, hydraulic system oil temperature and constant speed cylinder working environment.

constant speed cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a constant speed cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' constant speed cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the constant speed cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The constant speed cylinder mainly outputs linear motion and force. The constant speed cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston constant speed cylinder, plunger constant speed cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger constant speed cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

constant speed cylinder can not drive the load troubleshooting: oil pressure is too low. constant speed cylinder selection specifications are too small. Leakage in constant speed cylinder or associated hydraulic system element.

Answers to some questions about constant speed cylinder:

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲av午夜福利精品一区| 骚女人被大吊干视‘| 大鸡巴插入骚穴在线观看| 毛片日产av一区二区三区四区| 蜜臀AV无码国产精品尤物| 国产精品视频一区二区三区八戒| 成人黄色网破处在线播放| 免费看黑人操逼视频| 亚洲人成在线不卡网| 看小伙草白女人比的黄片| 美女大鸡操很多水在线看| 韩国无遮挡成人免费视频| 最新的亚洲欧美中文字幕| 国产午夜爽爽爽男女免费动漫AV| 被医生添奶头和下面好爽| 操我骚逼抽插视频| 91在线一区二区| 中文字幕亚洲精品女同一页| 日本潘金莲三级bd高清| 老熟妇高潮一区二区高清视频| 高清无码精品一区二区三区| 亚洲一区二区三区精品日韩| 国产成人无码AV一区二区三区| 日韩乱码一区二区三区中文字幕| 精品人妻一区二区三区日产乱码| 欧美日韩国产这里只有精品| 无码成人一区二区| 亚洲波多野结衣日韩在线| 日本高清一区二区三区水蜜桃| 国产伦精品一区二区三区视频抖音| 国产精品操大屁股老淑女| 亚洲AV无码一区二区三区天堂古| 亚洲激情无码视频| 欧美 日韩 亚洲 熟女| 日本黄色美女射精| 91精品国产综合久久久蜜| 精品一区二区av天堂色偷偷| 亚洲国际精品一区二区| 欧洲老妇人操大逼| 国产午夜久久精品一区四虎| 午夜理论理论亚洲激情|