亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

high pressure cylinder Sold to Luxembourg

Release time:2023-11-21 09:56:15 Hits: Current position: Home > News

This article mainly introduces:

Luxembourg hydraulic cylinder,high pressure cylinder manufacturer,high pressure cylinder

Luxembourg high pressure cylinder

(Luxembourg high pressure cylinder,produced by Hengyu Hydraulic Co., Ltd)

high pressure cylinder are widely used in Luxembourg,because of no need for deceleration device,long service life,smooth movement.So our company has designed high pressure cylinder for customers from Luxembourg.

Introduction to high pressure cylinder:

When using the high pressure cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the high pressure cylinder block. If the high pressure cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the high pressure cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the high pressure cylinder, so that the working efficiency of the high pressure cylinder is reduced.

If the seal of the high pressure cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and high pressure cylinder, and the phenomenon of "pulling the high pressure cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The repair method of high pressure cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

The oil high pressure cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Answers to some questions about high pressure cylinder:

How big is the motor and oil pump for the 80 cylinder?
Pump motor selection is not only related to cylinder diameter but also speed system, it is recommended to provide system diagram and speed requirements, generally speaking, most of the 80 cylinder on the market is equipped with 3-4KW motor, 10-20 oil pump.

What causes hydraulic cylinder oil leakage?
1. Internal leakage (1) The wear ring on the piston is seriously worn, leading to friction between the piston and the cylinder liner, and finally strain the cylinder liner, piston and seal; 2) Seal long-term use failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) The hydraulic oil is dirty, and a large number of impurities enter the cylinder and wear the piston seal to bad; 2. External leakage 1) cylinder inlet and outlet tubing joint cracking; (This I see in the actual work is still more) 2) The piston rod extension end with the piston rod seal damage, mostly due to the piston cylinder is caused by hair, but also caused by aging; 3) The seal between the extended end of the piston rod and the liner is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品你懂的在线资源| 帅哥大鸡巴操美女| 色网女人日本逼欧美| 妓女综合网在线观看| 亚洲一区二区三区四区国产| 美女被插入小穴涩涩视频| 国产精品白浆一区二区三区| 亚洲国产成人手机版| 极品一区二区三区av| 日韩高清精品一区有码在线| 怎么样操女人的逼亚洲Av黄片段| 欧美在线A片一区二区三区| 性色av少妇一区二区三区多人| 久久久五月性色视频| 精品麻豆国产免费一区二区三区| 9国产亚洲精品国产| 伊人久久丁香色婷婷啪啪| 大玩具猛插大bb| 九九在线视频热线视频精选| 国内精品久久久久精品97| 色网女人日本逼欧美| 欧美久久精品免费看C片| 男生操女生无马赛克免费| 久久久久久久 亚洲精品| 欧美精品日韩精品中文字幕| 被下药强奷到舒服的视频| 这里只有久久精品| 亚洲国产成久久成人综合一区| 欧美在线A片一区二区三区| 白虎美女被大基吧操| 亚洲精品自拍偷拍| 男人大鸡巴操小鲜肉视频| 天天爽夜夜爽夜夜爽一区| 欧美国产综合日韩一区二区| 老司机免费福利午夜入口| 几巴怪物操逼视频| 鸡巴操美女小穴羞羞视频| 亚洲精品自拍偷拍第一页| 日本不卡免费一区二区视频| 99爱国产精品免费视频| 日本熟妇 bbw|