亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

200 ton hydraulic cylinder Sold to UAE

Release time:2023-11-20 09:49:55 Hits: Current position: Home > News

This article mainly introduces:

UAE hydraulic cylinder,200 ton hydraulic cylinder manufacturer,200 ton hydraulic cylinder

UAE 200 ton hydraulic cylinder

(UAE 200 ton hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

200 ton hydraulic cylinder are widely used in UAE,because of no need for deceleration device,long service life,smooth movement.So our company has designed 200 ton hydraulic cylinder for customers from UAE.

Introduction to 200 ton hydraulic cylinder:

In the process of using the 200 ton hydraulic cylinder, sometimes such a problem will occur, the 200 ton hydraulic cylinder can not act immediately after the instruction of the 200 ton hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil 200 ton hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When purchasing the 200 ton hydraulic cylinder, try to clarify the following parameters of the 200 ton hydraulic cylinder: A. 200 ton hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or 200 ton hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right 200 ton hydraulic cylinder type can be found accurately and quickly.

If the piston rod and 200 ton hydraulic cylinder are stuck or the 200 ton hydraulic cylinder is blocked, at this time, no matter how to operate, the 200 ton hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the 200 ton hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the 200 ton hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the 200 ton hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil 200 ton hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical 200 ton hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the 200 ton hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Answers to some questions about 200 ton hydraulic cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩欧美视频在线观看不卡| 欧美精品日韩精品中文字幕| 为什么搜索不到裸体| 可以免费看污污片的软件| 18岁美女破处在线观看| 精品的极品美女一区二区三区| 日韩素人精品亚洲热一区| 久久久久精品无码专区喝奶| 成年女人永久看片视频 | 黑人大吊又操又添| 把女生操出水的视频| 69亚洲一级黄片| 2021最新热播国产一区二区| 亚洲精品自拍偷拍第一页| 从后面进入嗯啊视频| 丝袜片一区二区三区四区五区| 高清无码精品一区二区三区| 97青青草免费在线观看| 被医生添奶头和下面好爽| 最新中文字幕av不卡高清| 男女边吃奶边做边爱视频| 92婷婷伊人久久精品一区二区| 色999日韩自偷自拍美女| 爱男爽高潮鸡穴视频| 国产一级第一级毛片| 中文字幕在线资源第一页| 波多野吉衣一区在线观看| 国产日韩精品v一区二区| 激情久久久久久久久久久| 国产精品一区二区三区在线视| 国产女做a爱全免费视频| 性一乱一交一免费看视频| 久久综合色伊人九色91| 美女最骚逼逼视频| 浪潮AV色综合久久天堂| 韩美国男人叉女人| 日本高清一区二区三区水蜜桃| 无码成人一区二区| 午夜福利在线观看aaa| 免看一级a一片成人欧美| 国产一级a不收费|