亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

metallurgical cylinder Sold to Belgium

Release time:2023-11-20 09:49:46 Hits: Current position: Home > News

This article mainly introduces:

Belgium hydraulic cylinder,metallurgical cylinder manufacturer,metallurgical cylinder

Belgium metallurgical cylinder

(Belgium metallurgical cylinder,produced by Hengyu Hydraulic Cylinder Factory)

metallurgical cylinder are widely used in Belgium,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed metallurgical cylinder for customers from Belgium.

Introduction to metallurgical cylinder:

metallurgical cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the metallurgical cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the metallurgical cylinder. c. The metallurgical cylinder seal is extruded, if the O-ring is obviously extruded at the metallurgical cylinder seal, replace the metallurgical cylinder seal.

metallurgical cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards metallurgical cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the metallurgical cylinder guide is determined by the length of the stroke. Check the strength of metallurgical cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

When installing the metallurgical cylinder, the axial ends of the metallurgical cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the metallurgical cylinder, there is axial expansion. If the two ends of the metallurgical cylinder are fixed, all parts of the metallurgical cylinder will be deformed. When disassembling the metallurgical cylinder, it is strictly forbidden to hammer the metallurgical cylinder and the piston surface, such as the metallurgical cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

When the metallurgical cylinder is installed, the piston and the metallurgical cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the metallurgical cylinder head boss is easy to cause scars when it hits the inner surface of the metallurgical cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized metallurgical cylinders, only careful and careful operation can be avoided.

Answers to some questions about metallurgical cylinder:

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.

What is the cause of sound and vibration when the hydraulic cylinder is under load?
The main reason 1) may be that the load machinery has stuck phenomenon, and the resistance is large. 2) The hydraulic oil is not enough, or the filter is blocked by dirty things, and the oil is flooded. 3) There is a problem with the pump.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女操逼视频app| 男人把鸡巴插入女人| 午夜性福福利视频一区二区三区| 你懂的在线中文字幕一区| 久久精品人人爽人人爽快| 日韩午夜资源在线观看| 亚洲AV无码一区二区三区天堂古| 日日爱黄色毛片视频| 亚洲二亚洲欧美一区vr| 抽插肥嫩小穴的视频| 久久99热人妻偷产精品| 最新中文字幕av不卡高清| 国产伦精品一区二区三区视频抖音| 夫妻性生活视频在线直播| 亚洲国产精品一区亚洲国产| 欧美老熟妇又粗又大| 我最爱操女人的骚逼| 男女真人牲交高潮全过程| 几巴怪物操逼视频| 91kaobi视频在线| 香蕉国产精品偷在线| 9999热精品免费视频| 被春药女高潮抽搐喷水视频| 性一乱一交一免费看视频| 日本免费精品一区二区三区四区| 国产羞羞的视频在线观看| 欧美 日本 亚洲 国产| 日韩人妻精品一区二区三区| 波多野结衣高潮尿喷| 久久精品人人爽人人爽快| 又大黄又硬又爽免费视频| 日韩 欧美 成人 免费| 欧美一区二区三区男人的天堂| 美女逼男逼小穴小骚下载| 波多野结衣福利视频| 少妇毛片一区二区三区免费视频| 俩男人插下面的视频| 人妻夜夜添夜夜无码AV| 五月天婷婷一区二区三区久久| 美女日比视频播放| 亚洲日韩不卡一区二区三区|