亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

sanitation truck hydraulic cylinder Sold to Tunisia

Release time:2023-11-20 09:49:28 Hits: Current position: Home > News

This article mainly introduces:

Tunisia hydraulic cylinder,sanitation truck hydraulic cylinder manufacturer,sanitation truck hydraulic cylinder

Tunisia sanitation truck hydraulic cylinder

(Tunisia sanitation truck hydraulic cylinder,produced by Hebei Hengyu company)

sanitation truck hydraulic cylinder are widely used in Tunisia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed sanitation truck hydraulic cylinder for customers from Tunisia.

Introduction to sanitation truck hydraulic cylinder:

The repair method of the sanitation truck hydraulic cylinder: the repair of the sanitation truck hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

In order to ensure the service life of the sanitation truck hydraulic cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the sanitation truck hydraulic cylinder, causing damage to the seal and causing leakage in the sanitation truck hydraulic cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

Repair method of small range wear of oil sanitation truck hydraulic cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

sanitation truck hydraulic cylinders in series, parallel and series parallel. Series: In the sanitation truck hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the sanitation truck hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the sanitation truck hydraulic cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the sanitation truck hydraulic cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about sanitation truck hydraulic cylinder:

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操你的骚逼粉嫩AV| 国产精品久久一区二区三区夜色| 男人大鸡巴操女人的大逼| 东北大吊干东北少妇AV| 一级特黄大片色欧美精品| 丁香婷婷亚洲六月综合色| 鸡巴插骚逼视频欧美风格| 美女被插入小穴爆操视频| 国产精品亚洲1区2区| 亚洲波多野结衣日韩在线| 九九视频这里只有精品| 国产女做a爱全免费视频| 国产女做a爱全免费视频| 区国产精品搜索视频| 99草草视频在线精品| 亚洲欧美一区二区三区在| 欧美黄色三级成人小视频| 在线观看免费视频a v| 嗯嗯好硬好大啊老公| 欧美日韩综合在线一区| 国产熟女50岁一区二区| 91孕妇精品一区二区三区| 免费骚逼潮吹av| 国产精品无码一二区免费| 猛哥操女人B视频| 午夜精品在线视频| 国产精品粉嫩懂色av| 可以免费看黄的香蕉视频| 从后面狠狠的干白嫩少妇| 男插女逼啪啪啪软件| 精华欧美一区二区久久久| 欧美一区二区三区色婷婷月色| 欧美99热这里都是精品| 中文字幕在线观看第二页| 日本成人精品一区二区三区| 精品一区二区三区女性色| 熟女大屁股亚洲一区| 性一交一子一伦一乱| 日日狠狠久久888av| 无码av一区二区大桥久未| 国产精品亚洲一区二区三区下载|