亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Britain

Release time:2023-11-20 09:49:18 Hits: Current position: Home > News

This article mainly introduces:

Britain hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Britain reset cylinder

(Britain reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in Britain,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed reset cylinder for customers from Britain.

Introduction to reset cylinder:

reset cylinder hydraulic oil selection: The recommended working oil viscosity of the reset cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

The wear of the hard chromium plating layer of the reset cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

reset cylinder use should try to avoid sealing belt into the reset cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the reset cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the reset cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

The method of sleeve reset cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the reset cylinder can be significantly improved by rolling in the finishing of the inner holes of the reset cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

Answers to some questions about reset cylinder:

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

In a hydraulic system, a hydraulic pump has many hydraulic cylinders and hydraulic motors, and these executive components do not coordinate their actions with each other.
A load-sensitive variable pump can be used if these components sometimes need to work simultaneously and the power required is large. The required flow is distributed by the multi-way reversing valve, and the required flow and pressure changes are automatically adjusted by the hydraulic pump. Pressure reducing valves can be used for particularly low pressure circuits. Because you execute more components, the use of quantitative pump will cause a waste of energy, the system heat is large, not suitable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
韩国女主播一区二区视频| 女生小穴色色视频| 亚洲精品成人无码| 美女爽的嗷嗷叫免费| 欧美性一区二区三区五区| 国产精品熟女视频播放| 看小伙草白女人比的黄片| 把美女日到高潮喷水视频| 大男人在线无码直播| 最新日本一区二区三区免费看| 啊啊啊啊大鸡巴操我视频| 欧美另类在线观看| 人妻熟女av一区二区三区| 中文字幕av一区二区三区蜜桃| 麻豆91精品96久久久| 好爽轻点太大了太深了视频| 精品国产Av无码久久久一区二区| 97国产精品免费一二区| 久久99热人妻偷产精品| 91video国产一区| 欧美亚洲综合久久夜夜嗨| 日本高清一区二区三区在线观看| 欧美激情在线播放第一页| 亚洲国际精品一区二区| 国产欧美日本韩国一区二区| 天天免费的无码AV| 国产午夜爽爽爽男女免费动漫AV| 黑人猛操日本美女| 最新中文字幕av不卡高清| 男生插女生下面流出白色精液视频| 日本美女阴户射尿| 欧美猛男一区二区三区快播| 黑人与日本人妻中文字幕| 大肌巴日小个子女人视频| 美女逼男逼小穴小骚下载| 中文字幕av一区二区三区蜜桃| 国产精品欧美久久久久久| 鸡巴操美女小穴羞羞视频| 9亚洲导航深夜福利亚洲| 中文字幕乱码人妻一区二区三区| 国产一区二区三区三级88|