亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Uzbekistan

Release time:2023-11-20 09:49:15 Hits: Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Uzbekistan swager cylinder

(Uzbekistan swager cylinder,produced by Hengyu Hydraulic Cylinder Factory)

swager cylinder are widely used in Uzbekistan,because of no need for deceleration device,long service life,smooth movement.So our company has designed swager cylinder for customers from Uzbekistan.

Introduction to swager cylinder:

When using the swager cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the swager cylinder block. If the swager cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the swager cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the swager cylinder, so that the working efficiency of the swager cylinder is reduced.

The piston rod of the swager cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

If the swager cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the swager cylinder. The internal parts of the swager cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the swager cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the swager cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the swager cylinder bore processing is out of whack. Because the piston and swager cylinder, guide rail and piston rod are relative If the swager cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling swager cylinder weight composition and calculation. The weight of the swager cylinder is composed of the swager cylinder diameter, the outer diameter and weight of the swager cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

The swager cylinder should be vented: when the swager cylinder is installed or parked for a long time to work again, the air will penetrate into the swager cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the swager cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the swager cylinder, the oil is best entered and discharged from the highest point of the swager cylinder. swager cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Answers to some questions about swager cylinder:

How to calculate multistage cylinder volume?
When the multi-stage cylinder is extended, the largest cylinder is extended first, and when the largest cylinder stroke is completed, the second largest cylinder is extended again, the second largest cylinder stroke is completed, the third largest cylinder is extended again... Therefore, the cylinder extension length is less than the stroke of the largest cylinder, and the volume is the extension length times the inner hole area of the largest cylinder. The cylinder extension length is greater than the maximum cylinder stroke and less than (the largest cylinder stroke + the second largest cylinder stroke), and the volume is the largest cylinder stroke times the internal hole area of the largest cylinder + (the extension length - the largest cylinder stroke) times the second largest cylinder.

How to design the guide sleeve of cylinder diameter 400?
The purpose of the guide sleeve is to guide and seal. Therefore, it is necessary to look at the speed of the piston rod, working pressure and radial force. High speed, medium pressure, no (or very little) radial force, with a Steseal. Low speed and heavy load, medium radial force, combined seal. High speed and heavy load, large radial force, sealed with DU sleeve + copper ring + combination. The combination seal must have a lubricating oil passage, and a seal must be added to the outside of the oil passage.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩欧美一区二区三区在线视频| 亚洲午夜国产片在线观看| 极品美女销魂一区二区三区| 国产163黄网人看人人爽| 欧美国产综合日韩一区二区| 被医生添奶头和下面好爽| 亚洲AV无码一区二区三区系列| 在线观看国产黄色| 精品久久久久中文字幕人| 国产a一级毛片午夜剧院| 大鸡吧干小逼逼视频大全| 男人吃奶大鸡巴操逼视频| 亚洲精品国产人久久| 嗯嗯好硬好大啊老公| 久久久三级黄片免费视频| 中文字幕 av一区二区| 天天免费的无码AV| 欧美一区亚洲一区视频在线观看| 亚洲综合色88综合天堂| 被几个大屌老外轮操| 精品区在线导航视频观看| 亚洲高清中文字幕一区二区三区| 国产精品熟女视频播放| 日本十八禁大骚逼| 精品麻豆国产免费一区二区三区| 天天天天天干夜夜夜夜夜操| 中文字幕人妻一区二区三区久久| 非洲人粗大长硬配种视频| 国产一区曰韩二区欧美三区| 亚洲AV无码一区二区三区天堂古| 五月天亚洲激情综合av| 日韩激情精品久久久一区二区| 尤物AV无码国产在线看| 亚洲欧美国产原创一区二区三区| 欧美男女舔逼舔鸡巴视频| 夜夜38亚洲综合网| 国产中文字幕在线一区二区三区| 亚洲中文字幕在线无码一区二区| 好爽轻点太大了太深了视频| 欧美精品第一区二区三区| 日韩中文字幕一区二区高清|