亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Bulgaria

Release time:2023-11-20 09:49:13 Hits: Current position: Home > News

This article mainly introduces:

Bulgaria hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Bulgaria tension cylinder

(Bulgaria tension cylinder,produced by Hengyu Hydraulic Co., Ltd)

tension cylinder are widely used in Bulgaria,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed tension cylinder for customers from Bulgaria.

Introduction to tension cylinder:

If the seal of the tension cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

tension cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

tension cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The cavitation of the tension cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the tension cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Answers to some questions about tension cylinder:

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

What is a mold core cylinder?
Simple plastic parts can be directly pushed out by the ejector rod after injection molding, complex plastic parts can not be directly pushed out by the ejector rod after injection molding, to make the interference part active, control its position through the cylinder (injection molding into the mold, so that the shape of the plastic parts meet the demand, exit after opening the mold, so that the plastic parts are smoothly pushed out), This kind of cylinder is the mold core cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩午夜免费av在线| 18岁以下禁看美女的胸| 日韩久久中文字幕| 午夜性福福利视频一区二区三区| 大鸡巴操逼视频免费| 精品美女久久久久久嘘嘘| 制服丝袜国产在线第一页| 久久久久久国产A免费观看| 日本 视频 一区二区| 青娱乐欧美性爱视频| 91啪国线自产2019| 九九视频精品只有这里有| 精品福利一区二区三区在线观看| 日韩欧美一区二三区风间由美| 美女最骚逼逼视频| 国产天美传媒剧免费观看| 春宵福利导航91| 9亚洲导航深夜福利亚洲| 日韩在线视频不卡一区二区三区| 亚洲国产嫩草18久久久| 日本一区二区三区四区五| 啊啊啊别操了视频| 极品 操 抽插视频| 男人几把操女人嫩穴| 美女人的逼免费观看| 亚洲欧美一区二区三区在| 操女人b直播软件| 91性潮久久久久久久久| 日国产精品1卡二卡三卡| 尤物性生活午夜在线视频| 午夜国产三级一区二区三| 黑人巨茎和中国美女视频| 精品久久久久久不卡亚洲| 日韩一区二区三区夜色视频| 久久婷婷综合五月一区二区| 色偷偷影音先锋男人av| 亚洲国产日韩欧美高清片| 啊啊不要你那痛死爽死了直播一区| 美女操逼视频app| 被下药强奷到舒服的视频| 中日韩VA无码中文字幕|