亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to America

Release time:2023-11-19 14:06:37 Hits: Current position: Home > News

This article mainly introduces:

America hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

America stern plate hydraulic cylinder

(America stern plate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

stern plate hydraulic cylinder are widely used in America,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed stern plate hydraulic cylinder for customers from America.

Introduction to stern plate hydraulic cylinder:

When the piston speed of the stern plate hydraulic cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the stern plate hydraulic cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

The stern plate hydraulic cylinder is not the same as the stern plate hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the stern plate hydraulic cylinder can not be used as a high-power power component, but the stern plate hydraulic cylinder can be used as a relatively large power component, or the stern plate hydraulic cylinder system can be used.

When installing the stern plate hydraulic cylinder, the axial ends of the stern plate hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the stern plate hydraulic cylinder, there is axial expansion. If the two ends of the stern plate hydraulic cylinder are fixed, all parts of the stern plate hydraulic cylinder will be deformed. When disassembling the stern plate hydraulic cylinder, it is strictly forbidden to hammer the stern plate hydraulic cylinder and the piston surface, such as the stern plate hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

In order to ensure the service life of the stern plate hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

Answers to some questions about stern plate hydraulic cylinder:

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91偷自产一区二区三区蜜臀| 国产亚洲精品高清视频免费| 国产精品你懂的在线资源| 大鸡巴插我在线观看| 波多野结衣福利视频| 大鸡扒干美女BB直流水| 国产成人亚洲精品在线看| 亚洲一区二区女同性恋免费看| 国产免费无码一区二区视频无码| 日本不卡免费一区二区视频| 九九视频这里只有精品| 日本不卡免费一区二区视频| 日本成人精品一区二区三区| 国产乱精品一区二区三区视频了| 国产亚洲一区二区手机在线观看| 被公侵犯人妻少妇一区二区三区| 激情久久久久久久久久久| 91久久愉拍愉拍国产一区| 人妻含泪让粗大挺进| 国产欧美一二区不卡视频| 亚洲国产区男人本色| 白嫩在线亚洲观看| 国产亂倫近親相姦| 那种视频在线观看你懂的| 干美妞肛门在线播放| 国产 推油 性爱| 泰国无码AV片在线观看| 日本福利一区二区视频| 久久久久九九九国产精品| 国产一二三四五自产| 狂野国产性爱av| 中文字幕在线观视频| 美国业余自由摘花管| 在线 中文字幕 第一页| 成人黄色网破处在线播放| 欧美日韩精品视频在线第一区| 欧美亚洲综合一区二区三区| 白色紧身裤无码系列在线| 日韩在线视频不卡一区二区三区| 精品久久久久中文字幕人| 麻豆视频一级片在线观看|