亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Belarus

Release time:2023-11-19 14:06:03 Hits: Current position: Home > News

This article mainly introduces:

Belarus hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Belarus tension cylinder

(Belarus tension cylinder,produced by Hengyu Hydraulic Co., Ltd)

tension cylinder are widely used in Belarus,because of high work efficiency,excellent fatigue and impact resistance,smooth movement.So our company has designed tension cylinder for customers from Belarus.

Introduction to tension cylinder:

When the tension cylinder needs to be stored for a period of time, please follow the recommended methods: The tension cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tension cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tension cylinder should not be in direct contact with water vapor for a long time. The tension cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tension cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tension cylinder Before working, the tension cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tension cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The cavitation of the tension cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the tension cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

tension cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a tension cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' tension cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the tension cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The tension cylinder mainly outputs linear motion and force. The tension cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston tension cylinder, plunger tension cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger tension cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

When the tension cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the tension cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the tension cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about tension cylinder:

How many boom cylinders, bucket rod cylinders and bucket cylinders are there in a small single-bucket excavator?
one for bucket, one for forearm, only one piece for a small excavator under the big arm, two pieces for medium and large excavator.

What valve is used to control cylinder expansion?
Mainly use reversing valve, but the details of the control need hydraulic control valve, hydraulic control valve can be divided into direction control valve, pressure control valve, flow control valve. The valve controls the expansion of the cylinder is the direction control valve, that is, the reversing valve. What is the meaning of two-position three-way and three-position four-way of the reversing valve? Usually according to the different working positions that can stay after the spool is moved, it can be divided into: two-position valves, three-position valves and multi-position valves. According to the number of different slide valve channels can be divided into: two-way valve, three-way valve, four-way valve, five-way valve and multi-way valve. The name of the reversing valve is called the multi-position and multi-pass reversing valve according to its working position and the number of channels.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
无码社区在线观看| 欧美日韩国产这里只有精品| 欧美日韩国产这里只有精品| 国产亚洲欧美日韩在线观看一区| 国产欧美日韩一区二区在线观看| 欧美人人做人人爽人人喊| 精品美女久久久久久嘘嘘| 人妻人久久精品中文字幕| 久久久久久久久黄片观看| 国产品无码一区二区三区在线| 亚洲高清中文字幕一区二区三区| 亚洲精品国产综合一线久久| 亚洲男性天堂一区二区三区| 中文字幕无码区一区二区| 久久久中文字幕一区| 狗狗大鸡巴狂操美女| 最新免费高清无码片| 免费男人和女人黄片| 大阴茎交于大阴户黄片视频| 在线看免费无码a片视频| 99草草视频在线精品| 色逼色逼色逼色逼色逼色| 大胸瑟瑟黑丝午夜| 国产午夜爽爽爽男女免费动漫AV| 大鸡鸡插我骚逼视频| 人人摸人 人干人人草操| 强奷很舒服好爽好爽| 日本十八禁大骚逼| 粗大长内射女人视频| 精品福利一区二区三区在线观看| 精品免费福利片国产| 日本中文字幕无人区一区二区| 一色道久久88加勒比一| 中文字幕国产精品一区二区三区| 俩男人插下面的视频| 久久久三级黄片免费视频| 国产 日韩 亚洲 一区| 精品区在线导航视频观看| 久久久精品欧美一区二区三免费| 99热这里只有精品98| 欧美性一区二区三区五区|