亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hoister hydraulic cylinder Sold to Sudan

Release time:2023-11-18 17:15:15 Hits: Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,hoister hydraulic cylinder manufacturer,hoister hydraulic cylinder

Sudan hoister hydraulic cylinder

(Sudan hoister hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

hoister hydraulic cylinder are widely used in Sudan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed hoister hydraulic cylinder for customers from Sudan.

Introduction to hoister hydraulic cylinder:

How the cavitation of the hoister hydraulic cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the hoister hydraulic cylinder, resulting in corrosive damage to the parts.

The hoister hydraulic cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

hoister hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the hoister hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The hoister hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure hoister hydraulic cylinder can use 20 steel pipe, and the high pressure hoister hydraulic cylinder can use 45 steel pipe.

Answers to some questions about hoister hydraulic cylinder:

Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.

Is a hydraulic cylinder and a jack the same thing?
Strictly speaking, no. Although the hydraulic principle is used, and even some of the longer jacks are similar to the cylinder, the internal structure of the two is different. There is a check valve inside the jack. After the top lift, the check valve locks the hydraulic oil circuit, and the hydraulic oil only enters and does not exit after the check valve locks, and can be lowered to complete a reciprocating movement. The cylinder is usually connected to the distribution tube to control the movement, and works with a wide variety of distribution valves and distribution systems according to different needs. The jack only needs a simple check valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品国产自在现线看| 久久精品国产自清天天线| 欧美人与兽大屌肛交爆菊| 午夜性刺激在线视频免费| 男人大鸡巴操女人的大逼| 亚洲av熟妇高潮精品啪啪| 女人日比比视频免费| 插逼爽歪歪视频免费| 乱伦美女小骚货视频| 日韩精品诱惑一区?区三区| 亚洲天堂av一区二区在线观看| 天天爽夜夜爽夜夜爽一区| 欧美伦禁片在线播放| 97性无码区免费| 久久一区二区三区精华液介绍| 欧美综合区自拍亚洲综合| 老熟妇高潮一区二区高清视频| 国产午夜福利视频第三区| 亚洲天堂av一区二区在线观看| 欧美精品日韩精品中文字幕| 浪潮AV色综合久久天堂| 国产 欧美 日韩 黄片| 日韩午夜精品中文字幕| 大鸡插骚货人人色| 亚洲高清中文字幕一区二区三区| 鸡巴插骚逼视频欧美风格| 久久综合日韩亚洲精品色| 一级美女插逼百度| 国产午夜福利视频第三区| 中文字幕 av一区二区| 嗯啊好大好想要视频| 欧美人人做人人爽人人喊| 男人添女人下面免費视頻| 日韩欧美中文字幕国产精品| 操美女干逼调教捆绑视频| 欧美精品性做久久久久久| 女生的鸡鸡色色软件| 一区二中文字幕在线看国产一区| 无码人妻精品一区二区三区蜜桃| 久久99热东京热亲亲热| 91久久高清国语自产拍|