亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push bench hydraulic cylinder Sold to Burma

Release time:2023-11-17 13:21:52 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,push bench hydraulic cylinder manufacturer,push bench hydraulic cylinder

Burma push bench hydraulic cylinder

(Burma push bench hydraulic cylinder,produced by Hebei Hengyu company)

push bench hydraulic cylinder are widely used in Burma,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed push bench hydraulic cylinder for customers from Burma.

Introduction to push bench hydraulic cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Causes and countermeasures of oil push bench hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the push bench hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the push bench hydraulic cylinder is visibly scarred, the push bench hydraulic cylinder must be replaced. It can be pressurized at one end of the push bench hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most push bench hydraulic cylinder piston drift may not come from the push bench hydraulic cylinder, the above method to determine the push bench hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

When using the push bench hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the push bench hydraulic cylinder block. If the push bench hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the push bench hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the push bench hydraulic cylinder, so that the working efficiency of the push bench hydraulic cylinder is reduced.

When the oil pressure of the push bench hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about push bench hydraulic cylinder:

What is the reason for the hydraulic cylinder sticking out and not retracting?
There are two reasons: First, the problem with the seal, if there are two seals on the piston, the top seal is broken. Second, when the hydraulic pressure itself is designed, the rod cavity area is too small, so that the desired return force can not be achieved during the return trip. You can first check whether the coupling is damaged; Then see if the relief valve in the oil line block is blocked. If the use time is too long, it needs to be cleaned, the hydraulic oil is very dirty and can block oil block. Electromagnetic directional valves can also be checked, but the chance of problems is relatively small, unless there is a product problem.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大鸡巴插我在线观看| 欧美日韩亚洲人人夜夜澡| 操国产骚逼逼逼逼逼逼逼| 淫荡扣逼骚逼视频| 色噜噜在线一区二区三区| 久久久三级黄片免费视频| 精华欧美一区二区久久久| 国产高清一区二区三区四区色| 国产中文字幕在线一区二区三区| 亚洲男性天堂一区二区三区| 国产 日韩 亚洲 一区| 火辣美女的操大逼| 国产精品碰碰现在自| 尤物AV无码国产在线看| 美女呻吟翘臀后进爆白浆| 国产a一级毛片午夜剧院| 中文字幕乱码一区三区免费| 日本黑鸡吧黄色录像| 成人高清在线播放一区二区三区| 国产精品无码一二区免费| 欧美日韩一区二区成人在线| 日韩午夜资源在线观看| 24日本精品视频免费| 久久久久亚洲精品无码系列| 男人草女人的视频免费看| 国产亚洲精品高清视频免费| 大鸡巴射精在小穴动漫版| 亚洲综合一区国产精品| 丁香社区五月在线视频久| 亚洲日韩国产欧美久久久| 欧美精品国产一区二区在线观看| 巨屌抽插舔阴视频| 久久久久精品无码专区喝奶| 天天干天天操天天插| 亚洲精品自拍偷拍第一页| 国产日韩一区二区三区在线播放| 韩国三级a视频哪里看| 久久婷婷综合五月一区二区| 婷婷6月天丁香综合在线| 一区亚洲免费二区| 国产大码丝袜老熟女av|