亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Uganda

Release time:2023-11-17 13:21:51 Hits: Current position: Home > News

This article mainly introduces:

Uganda hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Uganda trunnion cylinder

(Uganda trunnion cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trunnion cylinder are widely used in Uganda,because of long service life,smooth movement,high work efficiency.So our company has designed trunnion cylinder for customers from Uganda.

Introduction to trunnion cylinder:

trunnion cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

The repair method of trunnion cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When the trunnion cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the trunnion cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Answers to some questions about trunnion cylinder:

What is the valve on the hydraulic cylinder?
Oil valve, relief valve, overload valve, explosion-proof valve, etc., these are very convenient to insert! The oil valve, the overload valve and the blasting valve are very important for larger cylinders. Manufacturers will not offer you the selection. You need to choose the values by yourself according to your system, pump, cylinder, environment, working conditions and other comprehensive consideration!

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品区在线导航视频观看| 日韩av一区二区高清不卡| 操美女干逼调教捆绑视频| 午夜精品福利一区二区三区蜜桃p| 国产精品欧美久久久久久| 欧美日韩国产这里只有精品| 日韩有码视频在线| 女人被躁到高潮嗷嗷叫小| 中文字幕 av一区二区| 草草久性色av综合av| 黄片观看骚货浪荡| 欧美真人性爱视频| 鸡巴插骚逼视频欧美风格| 啊啊好想被大鸡巴操视频| 男的日女生批网页| 黄色录像片操大逼的| 成人男女做爰免费视频网| 一级特一黄大片欧美久久| 人妻人久久精品中文字幕| 2021国产精品自在自线| 国产成人无码AV一区二区三区| 亚洲AV天堂一区二区香蕉| 可以免费看污污片的软件| 国产精品亚洲一区二区三区下载| 国产精品久久久69粉嫩| 又爽又粗又大又长的爆草| 视频一区二区三区日韩视频| 亚欧日韩国产在线| 色综合色狠狠天天综合色| 亚洲欧美国产原创一区二区三区| 亚洲精品成人无码| 精品麻豆亚洲欧美| 九九在线精品亚洲国产| 97国产精品免费一二区| a一级毛片免费高清在线| 精品一区二区久久久久无码| 最新国产亚洲亚洲精品A| 国产精品视频美熟女一区二区| 国产精品免费99久久久| 亚洲天堂av一区二区在线观看| 日本精品高清在线观看|