亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hoister hydraulic cylinder Sold to UAE

Release time:2023-11-17 13:21:20 Hits: Current position: Home > News

This article mainly introduces:

UAE hydraulic cylinder,hoister hydraulic cylinder manufacturer,hoister hydraulic cylinder

UAE hoister hydraulic cylinder

(UAE hoister hydraulic cylinder,produced by Hebei Hengyu company)

hoister hydraulic cylinder are widely used in UAE,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed hoister hydraulic cylinder for customers from UAE.

Introduction to hoister hydraulic cylinder:

What kind of process is used in the hoister hydraulic cylinder to make high-quality hoister hydraulic cylinder products: the body is the main component of the hoister hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The hoister hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the hoister hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the hoister hydraulic cylinder increases by 25%. If the service life of the hoister hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. hoister hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hoister hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and hoister hydraulic cylinder are stuck or the hoister hydraulic cylinder is blocked. At this time, no matter how to manipulate, the hoister hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the hoister hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

hoister hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

When the hoister hydraulic cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the hoister hydraulic cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

The hoister hydraulic cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

Answers to some questions about hoister hydraulic cylinder:

How to design the guide sleeve of cylinder diameter 400?
The purpose of the guide sleeve is to guide and seal. Therefore, it is necessary to look at the speed of the piston rod, working pressure and radial force. High speed, medium pressure, no (or very little) radial force, with a Steseal. Low speed and heavy load, medium radial force, combined seal. High speed and heavy load, large radial force, sealed with DU sleeve + copper ring + combination. The combination seal must have a lubricating oil passage, and a seal must be added to the outside of the oil passage.

How to exhaust hydraulic cylinder?
Exhaust: The hydraulic system generally does not have exhaust, the use of the tank can exhaust, the oil operation will bring the gas back to the tank, and the tank can be communicated with the atmosphere. The gas will escape from the oil.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本在线观看精品综合| 国产性生活视频免费| 欧美日韩国产精品视频一区| 国产在线观看污污污网站| 国产精品美女作爱视频| 中文字幕久久中文字幕综合网| 国产精品不卡在线视频| 国产精品一区二区97| 欧美色到久久88综合亚洲精品| 鼻子里天天有黄色鼻屎| 蜜臀av国产精品久久久久| 亚洲精品国产精品系列| 欧美老熟女多毛茸茸| 国产精品国产三级av| 中文字幕熟女一区二区三区| 日韩亚洲一区二区在线| 日本午夜福利在线视频| 亚洲AV手机在线观看| 欧美日韩一区二区中文字幕| 日韩一区二区三区视频| 日本成人免费一区二区三区| 接下来开始上伦理课免费观看| 在线十亚洲十欧美十日本专区| 接下来开始上伦理课免费观看| 日韩精品久久理论片| 美女草草影院在线观看视频| 日韩的一区二区另类免费| 三点水一个色是什么字| 国产精品熟女高潮久久99| 欧美高清性做爰销魂在线| 日韩无打码一区二区三区| 韩漫漫画在线免费看视频| 一区二区不卡99精品日韩| 中文字幕日韩电影在线| 久久久久成人精品免费播放寂寞少妇| 一区二区三区欧美激情| 亚洲国产精品久久久久网站| 亚洲区一区二区三区视频| 亚洲精品电影一区二区三区| 欧美国产日韩精品77上位| 亚洲精品国自产在线|