亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Indonesia

Release time:2023-11-08 08:11:54 Hits: Current position: Home > News

This article mainly introduces:

Indonesia hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Indonesia synchronous hydraulic cylinder

(Indonesia synchronous hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

synchronous hydraulic cylinder are widely used in Indonesia,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed synchronous hydraulic cylinder for customers from Indonesia.

Introduction to synchronous hydraulic cylinder:

Because of the slightly complex structure of the buffer synchronous hydraulic cylinder, sometimes there will be problems, such as when the synchronous hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

The commonly used buffer structure of the synchronous hydraulic cylinder is composed of a piston boss and a synchronous hydraulic cylinder head groove. When the piston moves close to the synchronous hydraulic cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

Disassembly synchronous hydraulic cylinder: When disassembly synchronous hydraulic cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the synchronous hydraulic cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the synchronous hydraulic cylinder.

When installing the synchronous hydraulic cylinder, the axial ends of the synchronous hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the synchronous hydraulic cylinder, there is axial expansion. If the two ends of the synchronous hydraulic cylinder are fixed, all parts of the synchronous hydraulic cylinder will be deformed. When disassembling the synchronous hydraulic cylinder, it is strictly forbidden to hammer the synchronous hydraulic cylinder and the piston surface, such as the synchronous hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

Answers to some questions about synchronous hydraulic cylinder:

What is a two-way hydraulic cylinder?
Bidirectional hydraulic cylinder definition: The bidirectional hydraulic cylinder uses the oil as the working medium, transmits the movement through the change of the sealing volume, and transmits the power through the pressure inside the oil. The two-way cylinder has at least two oil ports, which are used to connect the hydraulic tubing, and control the extension and retraction of the cylinder by pressing.

How does the self-locking cylinder work?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil circuit itself is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
一个色综合色综合色综合| 国产成人精品久久久成人| 韩国精品视频一区二区在线观看| 那种视频在线观看你懂的| 999久久久国产大美腿| 日本一区二区在线高清| 粉嫩小穴被大鸡巴操视频在线观看| 黑丝美女被操哭边操边尿| 大肉棒操小骚穴视频| 日韩欧美中文字幕国产精品| 国产精品国产三级国| 亚洲综合区欧美一区二区| 午夜福利在线观看aaa| 精品久久久久亚洲中文字幕| 国产激情内射免费精品| 大胸美女被c的嗷嗷叫视频| 国产精品自在拍首页| 中日美女毛5片一区二区三区| 美女大鸡操很多水在线看| 欧美日韩久久久一区二区三区| 找个日韩操逼的看看| 大胸美女被c的嗷嗷叫视频| 中文字幕在线观看第二页| 三级无码日B视频| 日本人色频在线看观| 欧美日韩综合在线一区| 国产午夜福利片无码视频| 国产精选三级在线观看| 日韩午夜经典福利| 国产欧美日本韩国一区二区| 国产一区曰韩二区欧美三区| 男女真人牲交高潮全过程| 国产欧美洲中文字幕床上| 亚洲国产成人手机版| 成人高清在线播放一区二区三区| 国产亚洲精品高清视频免费| 黑丝美女被操到高潮| 日韩欧美中文字幕国产精品| 中文字幕国产精品一区二区三区| 国产试看精品无码中| 白虎鲍鱼抠逼免费看|