亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Malaysia

Release time:2023-11-16 08:44:57 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Malaysia tailboard balance cylinder

(Malaysia tailboard balance cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailboard balance cylinder are widely used in Malaysia,because of no need for deceleration device,long service life,smooth movement.So our company has designed tailboard balance cylinder for customers from Malaysia.

Introduction to tailboard balance cylinder:

How the cavitation of the tailboard balance cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the tailboard balance cylinder, resulting in corrosive damage to the parts.

When the tailboard balance cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

The viscosity of the working oil used in the tailboard balance cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular tailboard balance cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about tailboard balance cylinder:

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

How to distinguish large cavity and small cavity of excavator rod cylinder ?
Single rod piston cylinder is a form of cylinder that is used relatively most, and the boom, bucket, dozer shovel cylinder are all in this form. Among them, the rodless cavity is also called the large cavity, and the rodless cavity is also called the small cavity. Therefore, the cylinder cavity on the side with the exposed piston rod is the small cavity, and the cylinder cavity on the side without the exposed rod is the large cavity.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
午夜精品福利一区二区三区蜜桃p| 老熟女被大鸡巴干| 国产乱子伦视频一区二区三区| 国内揄拍国内精品| 精品国产自在久国产应用| 99精品一级欧美片免费| 免费看黑人操逼视频| 国产精品免费99久久久| 新视觉亚洲三区二区一区理伦| 男生操女生无马赛克免费| 国产精品一区二区三区色噜噜| 日韩午夜资源在线观看| av黄色资源在线观看| 操老骚逼三级黄视频| 精品久久av免费一区二区三区| 夫妻性生活视频在线直播| 美女露胸露逼逼自慰| 日韩素人精品亚洲热一区| 国产精品久久久69粉嫩| 青青河边草直播免费观看| 日韩在线视频不卡一区二区三区| 粉嫩小穴被大鸡巴操视频在线观看| 日韩欧美视频在线观看不卡| 这里只有久久精品| 一个色综合色综合色综合| 欧美亚洲熟妇视频在线观看| 大玩具猛插大bb| 亚洲欧美一区二区三区孕妇| 被几个大屌老外轮操| 女人182毛片a级毛片| 潮中文字幕在线观看| 快速了解国产一级a爱片| 日韩欧美视频在线观看不卡| 在线 中文字幕 第一页| 久久久久国产AV成人片| 国内不卡的中文字幕一区| 夜夜嗨av少妇一二三区| 中国美女操逼的视频| 国产情侣色综合久久有码| 欧美丰满大屁股女人的逼被操视频| 粉嫩小穴被大鸡巴操视频在线观看|