亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Slovenia

Release time:2023-11-16 08:44:12 Hits: Current position: Home > News

This article mainly introduces:

Slovenia hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Slovenia supporting cylinder

(Slovenia supporting cylinder,produced by Hengyu Hydraulic Co., Ltd)

supporting cylinder are widely used in Slovenia,because of clever hydraulic energy conversion,no need for deceleration device,long service life.So our company has designed supporting cylinder for customers from Slovenia.

Introduction to supporting cylinder:

supporting cylinder use should try to avoid sealing belt into the supporting cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the supporting cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the supporting cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

If the supporting cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the supporting cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow supporting cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the supporting cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the supporting cylinder includes the leakage caused by excessive wear of the supporting cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and supporting cylinder, and the phenomenon of "pulling the supporting cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

The supporting cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the supporting cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the supporting cylinder wall due to the stiffness and the weight of the parts, causing scars.

When the supporting cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the supporting cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about supporting cylinder:

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

In hydraulic equipment, is the motor power related to the cylinder pressure holding time?
Irrelevant. The motor only drives the plunger in the hydraulic cylinder of the oil pump to extend out, and stops when the set pressure is reached; The length of the pressure holding time is related to the sealing degree of the hydraulic cylinder and the solenoid valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美成人3p视频在线观看| 亚洲AV无码之日韩精品| 久久久久精品欧美日韩精品| 99久久精品国产一区二区三区?| 91精品国自产在线播放| 欧美日韩精品免费一级| 国产亚洲一区二区三区午夜| 人妻少妇精品视频无码专区| 亚洲最大国产精品一区| 亚洲精品国产成人99久久6| 亚洲国产精品一区二区三区久久| 日韩一区二区三区视频| 中文精品久久久久国产网址| 亚洲高潮久久久久久| 欧美一区二区三区成| 亚洲精品国产第一区三区| 2020国自产拍精品网站| 人人妻人人澡av天堂香蕉| 国产一区二区精品久| 国产亚洲综合欧美一区| 在线播放亚洲欧美日韩| 欧美日韩精品一区丁香| 国产成人亚洲综合91精品首页| 极品少妇欧美一区二区| 欧美日韩国产综合在线视频| 97精品国产综合久久| 操久久久久久久久久久久久久久久久| 国产精品综合久久久久久| 韩漫漫画在线免费看视频| 91精品无码中文字幕在线| 中文字幕久久中文字幕综合网| 亚洲国产精品久久久久麻| 中文字幕人妻女同一区| 日本韩国亚洲欧美一区二区三区| 国产白嫩精品久久久| 人妻少妇精品视频无码专区| 五月天丁香花婷婷色| 亚洲欧美中文在线另类| 国产精品午夜福利在线观看| 亚洲欧美成人激情在线| 99国产精品视频在线|