亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Latvia

Release time:2023-11-15 10:42:17 Hits: Current position: Home > News

This article mainly introduces:

Latvia hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Latvia self-locking hydraulic cylinder

(Latvia self-locking hydraulic cylinder,produced by Hebei Hengyu company)

self-locking hydraulic cylinder are widely used in Latvia,because of long service life,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed self-locking hydraulic cylinder for customers from Latvia.

Introduction to self-locking hydraulic cylinder:

In the case of serious wear on the inner surface of the self-locking hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the self-locking hydraulic cylinder manufacturing process for replacement. The self-locking hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

How to determine the working pressure of the self-locking hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, self-locking hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

self-locking hydraulic cylinder use should try to avoid sealing belt into the self-locking hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the self-locking hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the self-locking hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

The pressure of the sliding surface of the self-locking hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the self-locking hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Answers to some questions about self-locking hydraulic cylinder:

Is there a way to make the cylinder stop pushing when it hits something hard during the process of pushing?
The simplest solution is to press the stop switch, this switch has a mechanical type, touch the object on the action or send a stop signal, through the operation of the motor control cylinder; There is also an induction switch, that is, when the hydraulic cylinder expands to the range of the induction switch can sense the signal, it sends a signal to let the motor act, resulting in the corresponding action of the cylinder.

Structural characteristics of the plunger cylinder? (1) The plunger hydraulic cylinder is a single-acting hydraulic cylinder, which can only move in one direction by hydraulic pressure, and the return trip of the plunger depends on other external forces or the weight of the plunger; (2) The plunger is only supported by the cylinder liner and is not in contact with the cylinder liner, so the cylinder liner is easy to process, so it is suitable for long stroke hydraulic cylinder; (3) the total pressure of the plunger during work, so it must have sufficient stiffness; (4) The weight of the plunger is often large, and it is easy to sag due to its own weight when placed horizontally, resulting in wear of the seals and guide side, so its vertical use is more favorable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产欧美洲中文字幕床上| 亚洲一级片在线播放| 丰满少妇被强入在线观看| 国产精品午夜小视频观看| 亚洲午夜福利视频在线| 国产亚洲欧美中文日韩| 啊啊啊操我视频大全| 国产精品你懂的在线资源| 大鸡巴插入骚穴在线观看| 农村胖肥胖女人操逼视频| 日韩欧美中文字幕国产精品| 久久久中文字幕在线视频| 亚洲午夜国产片在线观看| 国产精品无码一二区免费| 日本不卡免费一区二区视频| 色欲色欲色视频综合| 激烈18禁高潮视频免费| 男男大鸡巴操小屁眼视频| 欧美性一区二区三区五区| 操鸡巴奶子在线观看| 日韩视频在线网页| 久久国产精品成人18p| 呦交小u女国产精品99| 99久久九九爱精品国产| 怎么样操女人的逼亚洲Av黄片段| 欧美成人精品一区二区免费看| 看一下日本人插逼逼洞视频| 内射白嫩少妇超碰| 美女日逼视频免费| 伊人久久久久久久久香港| 色狠狠久久av北条麻妃| 中文字幕一区二区日韩精品蜜臂| 久久久精品欧美一区二区三免费| 藏经阁91福利私人试看| 火辣美女的操大逼| 美女大鸡操很多水在线看| 久久久久久久久中文字幕| 国产欧美一二区不卡视频| 色噜噜在线一区二区三区| 欧美 日韩 激情 在线| A级毛片高清视频|