亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Sri Lanka

Release time:2023-11-15 10:41:58 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Sri Lanka stacker cylinder

(Sri Lanka stacker cylinder,produced by Hengyu Hydraulic Co., Ltd)

stacker cylinder are widely used in Sri Lanka,because of no need for deceleration device,long service life,smooth movement.So our company has designed stacker cylinder for customers from Sri Lanka.

Introduction to stacker cylinder:

The wear of the hard chromium plating layer of the stacker cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

stacker cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stacker cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When using the stacker cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the stacker cylinder block. If the stacker cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the stacker cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the stacker cylinder, so that the working efficiency of the stacker cylinder is reduced.

The stacker cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

Answers to some questions about stacker cylinder:

There are four cylinders in the front top of the dump truck. When the second cylinder is lifted to half the height, it suddenly falls back more than 30 cm or so, and the cylinder continues to lift.
The problem is the cylinder, the second section of the different strength of the heart. When the oil supply resistance is small, the first out, when the power is not moving, the cylinder needs to be strong, because the second section needs to pop it out after a while when the pressure is large, the oil can not keep up, so it falls back, and the oil continues to keep up.

How is the hydraulic cylinder selected in the mechanical design manual?
First of all, it is necessary to meet your work needs, and the second is to meet the structural space of the cylinder and accessories. Three to consider the other parameters of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大肉棒操小骚穴视频| 鸡巴插骚逼视频欧美风格| 日本十八禁大骚逼| 精品国产自在现线看| 欧美大鸡巴操穴日韩| 大鸡吧干小逼逼视频大全| 女人182毛片a级毛片| 美国大骚逼啊啊啊| 成人刺激性视频在线观看| 欧美老熟妇又粗又大| 69国产精品久久久久久人| 欧美一区二区三区四公司| 中国老女人 操逼 视频| 国产精品久久一区二区三区夜色| 大鸡巴狂插嫩逼视频| 日本一区二区三区高潮喷吹| 欧美一区二区三区四区五区精品| 美女扒开腿让男人桶爽揉| 胸大裸体美女视频| 九九在线精品亚洲国产| 翘臀小穴在线观看| 欧美高清在线观看一区二区三区| 亚洲欧美一区二区爽爽爽| 欧美亚洲干妞内射| 韩国女主播一区二区视频| 天天爽夜夜爽夜夜爽一区| 西瓜在线看免费观看视频| 鸡巴操美女小穴羞羞视频| 乱伦美女小骚货视频| 国产福利一区二区精品秒拍| 一区二区国产精品免费视频| 国产无码福利一区| 2021国产一区二区岛国| 日韩美女一区二区三区香蕉视频| 色熟妇人妻久久中文字幕| 99视频在线看免费视频| 美女被插入小穴爆操视频| 久久久精品欧美一区二区三免费| 在线视频观看一区| 精品一区二区三区乱码中文字幕| 中文字幕日韩亚洲|