亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

spring return cylinder Sold to Morocco

Release time:2023-11-14 08:41:20 Hits: Current position: Home > News

This article mainly introduces:

Morocco hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

Morocco spring return cylinder

(Morocco spring return cylinder,produced by Hengyu Hydraulic Cylinder Factory)

spring return cylinder are widely used in Morocco,because of no need for deceleration device,excellent temperature resistance,no transmission clearance.So our company has designed spring return cylinder for customers from Morocco.

Introduction to spring return cylinder:

In recent years, the processing process of the spring return cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

There are some honeycomb holes in the inner wall of the spring return cylinder, piston or piston rod surface. How is this formed? When we repair the spring return cylinder, we can see that there are some honeycomb holes on the inner wall of the spring return cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the spring return cylinder is targeted to prevent. Is very necessary.

In the case of serious wear on the inner surface of the spring return cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the spring return cylinder manufacturing process for replacement. The spring return cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Repair method of small range wear of oil spring return cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

Answers to some questions about spring return cylinder:

Why hydraulic cylinder load can not rise?
The hydraulic cylinder does not top up indicates that the pressure of the working chamber of the hydraulic cylinder is insufficient, and the following circumstances can lead to insufficient pressure: 1) The relief valve of the hydraulic system cannot establish pressure, elimination method: check whether the pressure setting screw of the relief valve is screwed to the appropriate position. If it is an electromagnetic relief valve, please check the power-on condition. 2) The hydraulic system pipeline is connected incorrectly, when P and T are connected, this must be checked and excluded; 3) Excessive leakage in the hydraulic cylinder, resulting in (only for double-acting cylinders); 3) No hydraulic oil into the working chamber of the hydraulic cylinder, elimination method: first disassemble the hydraulic pipe connecting the reversing valve and the hydraulic cylinder, and then control the reversing valve, and observe whether there is hydraulic oil flowing out of the reversing valve.

How to calculate the speed of cylinder weight decline?
To reduce the weight of the cylinder, the necessary condition is that the weight of the piston rod + external load is greater than the friction between the seal ring and the cylinder. There are many reasons for this, first of all, consider the reasons of the cylinder itself, the piston in the cylinder and the sealing ring on the piston rod will play a reaction force on the weight of the cylinder (because of friction), which depends on the tightness of the sealing ring and the cylinder. Secondly, what is connected under the piston rod of the cylinder and how much weight there is. And the way the cylinders are arranged, is it completely vertical. Anyway, in fact, the most important thing is to see how much the bore of the oil hole of the piston rod cavity of your cylinder is. For example, if the hole in the lower chamber of the cylinder is small, as thin as a needle, then its descent rate will be slow.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品国产99亚洲一区二区三区| 99精品一级欧美片免费| 最新黄色A级一短片| 18岁美女破处在线观看| 狗狗大鸡巴狂操美女| 老熟妇高潮一区二区高清视频| 欧美 日韩 国产 自拍| 中文字幕av一区二区三区蜜桃| 男人天堂av在线免费看| 久久精品欧美精品免费观看| 女生的鸡鸡色色软件| 操美女逼逼色逼网| 91video国产一区| 黑人巨茎和中国美女视频| 美女骚逼被操出白浆| 韩国无玛黄片毛片| 天天干天天操天天插| 爽妇网国产精品24| 国产午夜精品美女视频露脸| 两人爽爽爽无码免费视频| 性一乱一交一免费看视频| 99久久精品国产一区二区成人了| 操老骚逼三级黄视频| 亚洲国产无线码在线| 日本高清一区二区三区不卡| 无码中文字幕免费一区二区三区| 亚洲 欧美 精品 高清| 亚洲v国产v天堂a无码| 久久一级高潮a免费| 美女被操的流水AV| 阴茎大头插少妇蜜穴视频| 韩国女主播一区二区视频| 亚洲av午夜一区二区| 欧美亚洲另类天天综合网| 日韩精品诱惑一区?区三区| 亚洲精品自拍偷拍第一页| 看一下日本人插逼逼洞视频| 国产163黄网人看人人爽| 黄网官方在线观看| 亚洲午夜国产片在线观看| 久久久中文字幕在线视频|