亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Poland

Release time:2023-11-14 08:41:15 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Poland supporting cylinder

(Poland supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

supporting cylinder are widely used in Poland,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed supporting cylinder for customers from Poland.

Introduction to supporting cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Factors that should be considered when selecting the oil seal in the supporting cylinder: some specific factors should be taken into account when selecting the oil seal in the supporting cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: supporting cylinder diameter, piston rod diameter, piston rod and piston groove size, supporting cylinder working pressure, supporting cylinder movement speed, hydraulic system oil temperature and supporting cylinder working environment.

Before the supporting cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

The repair method of supporting cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about supporting cylinder:

What do cylinder internal leakage and external leakage mean?
Internal leakage means that the piston seal in the cylinder is not strict, there is a leak between the two chambers of the cylinder, the oil is still in the cylinder, and the external leakage is that the oil leaks to the outside of the cylinder.

Need a hydraulic cylinder, vertical upward 10 seconds to lift 20 tons of weight up 2 meters, how large cylinder and rod, how much pressure to use the plunger pump and how big?
The first thing to determine the system pressure, let's say 25 mpa, can take into account cost and performance. 1 Cylinder area 20000/250=80 square cm cylinder diameter (80/3.14) squared x2=200 mm 2 cylinder volume 80x200=16000 ml =16 L 3 Required pump flow 16x60/10=96 L/min 4 Power 96x25/55=43 kW 45 kW motor is available.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本男人捅女人机机| 日本免费精品一区二区三区四区| 久久99热精品在线观看| 69国产精品久久久久久人| 鸡巴抽插逼逼视频| 国产色哟哟精选在线播放| 麻豆国产欧美一区二区三区r| 99爱国产精品免费视频| 精品无码一区二区三区无码| 久久久久久国产A免费观看| 操我骚逼抽插视频| 帅哥大鸡巴操美女| 人人摸人 人干人人草操| 国产情侣色综合久久有码| 日本欧美中文字幕| 日本福利一区二区视频| 黄片大鸡吧操小逼| 最新AV中文字幕在线看| 日韩av一区二区三区激情在线| 欧美大胆a级视频 一本| 欧美尤物操逼毛茸茸真爽| 日本免费一区二区在线| 三男狂插小穴穴视频| 中文字幕在线观一区二区| 国产精品操大屁股老淑女| 日韩欧美一区二三区风间由美| 大鸡巴狂插嫩逼视频| 97性无码区免费| 60秒动态视频在线观看| 国产精品午夜小视频观看| 国产精品国产精黄 | 色老头av亚洲三区三区| 男人的下面进女人的下面在线观看| 综合欧美日韩一区二区三区| 阴茎大头插少妇蜜穴视频| 亚洲综合色88综合天堂| 亚洲综合极品香蕉久久网| 无码爆一二三区免费视频| 亚洲男人的天堂2021| 亚洲女同一区二区三久久精品| 爱爱视频小抽插动漫|