亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

yg series hydraulic cylinder Sold to Kenya

Release time:2023-11-08 08:11:36 Hits: Current position: Home > News

This article mainly introduces:

Kenya hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

Kenya yg series hydraulic cylinder

(Kenya yg series hydraulic cylinder,produced by Hengyu Group)

yg series hydraulic cylinder are widely used in Kenya,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed yg series hydraulic cylinder for customers from Kenya.

Introduction to yg series hydraulic cylinder:

yg series hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The oil yg series hydraulic cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

If the seal of the yg series hydraulic cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and yg series hydraulic cylinder, and the phenomenon of "pulling the yg series hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

How to determine the working pressure of the yg series hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, yg series hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about yg series hydraulic cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to set the stroke of the cylinder?
Self-design should be based on product demand and practical application. The stroke of standard cylinder depends on the parameters the customer requires. The hydraulic cylinder is a linear motion actuator whose output force is proportional to the effective area of the piston and the pressure difference on both sides. Its function is to convert hydraulic energy into mechanical energy. The input of the hydraulic cylinder is the flow rate and pressure of the fluid, and the output is the speed and force of the linear motion. The piston of the hydraulic cylinder can complete the linear reciprocating movement, and the linear displacement of the output is limited. Hydraulic cylinder is an energy conversion device that converts hydraulic energy into mechanical energy of reciprocating linear motion. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston and piston rod, sealing device, buffer device and exhaust device.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品女同久久久久久| 中文亚洲欧美日韩国产| 久久综合视频中文字幕| 韩国爱情电影年轻的母亲| 漫画韩漫画免费在线观看| 欧美一级精品片在线看| 亚洲欧美一区二区久久| 国产目拍亚洲精品一区二区| 一区二区三区久久九九| 日本精品va在线观看| 99久久精品国产一区二区三区?| 亚洲人妻一区二区久久| 日本一区二区三区综合| 欧美一级精品片在线看| 精品国产_亚洲人成在线| 一区二区三区欧美日本| 日韩欧美中文字幕一区二区| 精品国产片亚洲一区| 国产白嫩精品久久久| 亚洲欧美另类色视频| 国产精品熟女视频网站| 日本一区二区三区中文字幕八戒视频| 一区二区不卡99精品日韩| 婷婷激情网五月天亚洲| 国产在线观看一区视频| 国偷自产av一区二区三区| 丰满的大乳老师三级在线观看| 亚洲mm视频网站在线播放| 日本大香焦免费视频| 久久精品成人免费国产| 高清国产午夜精品久久久久久| 国产欧美精品区一区二区三区竹菊| 亚洲欧洲日韩综合网站| 中文字幕久久中文字幕综合网| 韩国午夜理伦三级理论电影| 午夜亚洲在在线观看| 91国产精品免费观看| 国产三级网络视频在线观看| 国产白丝theporn| 久久久久久亚洲一区二区| 国产在线观看一区视频|