亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

rack cylinder Sold to Mexico

Release time:2023-11-13 11:19:51 Hits: Current position: Home > News

This article mainly introduces:

Mexico hydraulic cylinder,rack cylinder manufacturer,rack cylinder

Mexico rack cylinder

(Mexico rack cylinder,produced by Hebei Hengyu company)

rack cylinder are widely used in Mexico,because of high work efficiency,high work efficiency,clever hydraulic energy conversion.So our company has designed rack cylinder for customers from Mexico.

Introduction to rack cylinder:

If air enters the hydraulic system, the rack cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

The cavitation of the rack cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the rack cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

The pressure of the sliding surface of the rack cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the rack cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

rack cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Answers to some questions about rack cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操大屌粉的小穴视频| 好爽又高潮了毛片在线看| 被大鸡巴操淫液视频| 亚洲综合网伊人中文| 彩虹网免费视频在线观看| 澳门一区二区免费下线观看| 火辣美女的操大逼| 欧美大鸡巴操大骚逼| 日本六十五十熟女一级黄色| 国产精品一区二区在线观看91| 大肉棒操小骚穴视频| 美女主播被操流水| 97人妻精品一区二区三区视频| 精品一区二区三区乱码中文字幕| 国产女做a爱全免费视频| 精品区在线导航视频观看| 99久久99久久精品视频| 男人大鸡巴操女人的大逼| 少妇精品久久久一区二区免费| 亚洲欧美一区二区三区孕妇| 黑人插中国女人逼| 操大美女逼射精视频| 国产成人AV剧情| 人妻熟女av一区二区三区| 日本公共厕所mmm撒尿| 久久久久人妻一区精品加勒比| 强奷很舒服好爽好爽| 免费国产香蕉视频在线观看| 国产亚洲一区白丝在线观看| 我想看操小嫩逼大片| 美女日逼视频免费| 日韩欧美视频在线观看不卡| 精品精品国产一区二区性色av| 美女大骚逼幸福遍穴| 久久久国产精品亚洲无码| 农村胖肥胖女人操逼视频| 日韩人妻无码中字一区二区| 男人草女人的视频免费看| 快日我啊好爽日我逼| 黑人大吊性交啪啪啪| 大香蕉操逼小视频|