亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Slovakia

Release time:2023-11-13 11:19:49 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Slovakia stern plate hydraulic cylinder

(Slovakia stern plate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stern plate hydraulic cylinder are widely used in Slovakia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed stern plate hydraulic cylinder for customers from Slovakia.

Introduction to stern plate hydraulic cylinder:

The stern plate hydraulic cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

When purchasing the stern plate hydraulic cylinder, try to clarify the following parameters of the stern plate hydraulic cylinder: A. stern plate hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or stern plate hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right stern plate hydraulic cylinder type can be found accurately and quickly.

The stern plate hydraulic cylinder should be vented: when the stern plate hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the stern plate hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the stern plate hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the stern plate hydraulic cylinder, the oil is best entered and discharged from the highest point of the stern plate hydraulic cylinder. stern plate hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When installing the stern plate hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stern plate hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the stern plate hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stern plate hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stern plate hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about stern plate hydraulic cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

What is the role of the cylinder on the plastic mold? The oil cylinder plays a great role in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the oil cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product, sometimes customers require to use hot runner, the price is more expensive, but there are many benefits. It can save raw materials and shorten the molding cycle.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品一区二区在线观看91| 久久综合日韩亚洲精品色| 挺进绝色邻居的紧窄小肉| 大鸡巴操屁眼无码| 97国产精品免费一二区| 亚洲福利左线观看| 欧美一区二区三区男人的天堂| 日本精品久久人妻一区二区三区| 欧美成人精品一区二区免费看| 国产又粗又猛又色又免费| 国产熟女50岁一区二区| 性色av少妇一区二区三区多人| 在线观看免费视频a v| 国产精品999午夜激情| 日韩一区二区三区国色天香| 亚洲欧美日韩另类| 久久久久人妻一区精品加勒比| 亚洲一区二区三区日本在线| 精品一区二区视频在线观看| 国产色哟哟精选在线播放| 看一下日本人插逼逼洞视频| 国产一级第一级毛片| 亚洲精品成人无码app| 热精品韩国毛久久久久久| 影音先锋亚洲中文综合网| 熟妇人妻无乱码中文字幕| 大鸡巴射在穴穴里的视频| 少妇被黑人入侵在线观看| 久久亚洲精品无码AV宋| 大肉棒操小骚穴视频| 国产精品毛片一区视频播| 欧美猛男一区二区三区快播| 欧美一级特黄大片在线看| 嗯啊好大好想要视频| 人妻夜夜添夜夜无码AV| 久久久久久国产A免费观看| 尤物性生活午夜在线视频| 彩虹网免费视频在线观看| 非洲男生操男生屁眼视频| 欧美99热这里都是精品| 大胸美女被c的嗷嗷叫视频|