亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Bolivia

Release time:2023-11-13 11:19:29 Hits: Current position: Home > News

This article mainly introduces:

Bolivia hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Bolivia trunnion cylinder

(Bolivia trunnion cylinder,produced by Hengyu Group)

trunnion cylinder are widely used in Bolivia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from Bolivia.

Introduction to trunnion cylinder:

The oil trunnion cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Piston trunnion cylinder is widely used in hydraulic transmission. When the trunnion cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the trunnion cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the trunnion cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

In recent years, the processing process of the trunnion cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

After chrome plating of the piston rod of the trunnion cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about trunnion cylinder:

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

What is the problem that the cylinder stroke is not in place?
1. Mechanical cause: the piston rod bends; If there is a synchronous cylinder, the stroke of the two cylinders may be different. 2. Hydraulic reason: the system back pressure is too large; The actuator load increases while the system pressure decreases. The electric is not sent, the reversing valve is not reset or stuck, the oil is too dirty, there is gas in the system, the external inertia load is too large, and the cylinder stroke is not in place.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美国毛片亚洲社区成人看| 无码人妻丰满熟妇区精品| 国产精品视频一区二区三区八戒| 交换夫妇4中文字幕| 成人刺激性视频在线观看| 日韩美女在线视频一区不卡| 色熟妇人妻久久中文字幕| 日本二区在线观看| 影音先锋亚洲中文综合网| 操老骚逼三级黄视频| 日本韩国国产精品一区| 3色w九九久久男人皇宫宕| 中文有码无码人妻在线看| 亚洲一区二区三区精品日韩| 欧美另类在线观看| 欧美丰满大屁股女人的逼被操视频| 99久久久国产精品k影| 欧美日韩亚洲人人夜夜澡| 老色鬼精品视频二区三区| 狠狠色伊人亚洲综合成人| 中国毛茸茸的操逼| 国产区高清在线一区二区三区| 精品久久久久中文字幕人| 极品 操 抽插视频| 日韩 欧美 一区 二区三区| 国产高清免费一级a久久| 97超级免费视频在线观看| 粉嫩小穴被大鸡巴操视频在线观看| 欧美一区二区三区高清性群p| 藏经阁91福利私人试看| 亚洲AV无码一区二区三区系列| 两人爽爽爽无码免费视频| 亚洲狠狠插狠狠搞狠狠摸| 伊人久久久久久久久香港| 美女亚洲福利视频| 老熟妇高潮一区二区高清视频| 大狼狗插阴道视频| 精品一区二区三区乱码中文字幕| a一级毛片免费高清在线| 久久亚洲精品无码AV宋| 欧美精品第一区二区三区|