亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

supporting cylinder Sold to Oman

Release time:2023-11-13 11:19:27 Hits:134 Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Oman supporting cylinder

(Oman supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

supporting cylinder are widely used in Oman,because of long service life,smooth movement,high work efficiency.So our company has designed supporting cylinder for customers from Oman.

Introduction to supporting cylinder:

The supporting cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

How to determine the working pressure of the supporting cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, supporting cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Before purchasing the supporting cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

The supporting cylinder is mainly composed of body, piston, piston rod, supporting cylinder head, supporting cylinder bottom, piston rod head and related auxiliary devices. The piston divides the supporting cylinder into two chambers, and moves reciprocally in the supporting cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the supporting cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the supporting cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the supporting cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the supporting cylinder bottom and the supporting cylinder head is serious, so the buffer deceleration should be set at both ends of the supporting cylinder The working medium of the supporting cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; supporting cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the supporting cylinder: The buffer structure of the supporting cylinder is to prevent the piston from colliding with the supporting cylinder head at the end of the stroke.

Answers to some questions about supporting cylinder:

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
99久久精品国产一区二区成人了| 国产A级黄片下载| 精品少妇一区二区三区中文字幕| 久久噜噜噜久久熟女精品| 无码av一区二区大桥久未| a一级毛片免费高清在线| 操女人逼逼骚逼逼| 束缚久久久久久免费高潮| 日韩人妻无码中字一区二区| 中文国产成人精品久久久| 大鸡巴日小美女明星的BB| 中文字幕欧美人妻在线| 人妻波多野结衣爽到喷水| 农村胖肥胖女人操逼视频| 丁香社区五月在线视频久| 高清最新操逼吃鸡巴视频| 鸡巴插骚逼视频欧美风格| 女人被男人躁爽色欲国产| 大鸡吧插美女嫩逼| 骚狐狸免费在线观看视频| 日本一二区视频在线观看| 美女穿黑丝被大鸡巴猛操| 欧美大鸡巴捅骚逼吃| 亚洲欧洲综合成人综合网| 啊啊好想被大鸡巴操视频| 在线观看国产日韩欧美一区二区| 操的我的逼逼好爽好多水| 久久精品小视频/| 黑人妖大鸡吧操逼| 欧美一区二区三区四区五区精品| 日本人妻与家公的伦理片| 国产伦精品一区二区三区视频抖音| 骚逼被操视频拳交| 黑人大鸡巴日小逼| 我要看成人免费毛片| 操女人大逼视频下载| 国产精品三级一区二区| 亚洲国产无线码在线| 日韩中文字幕一区二区高清| 少妇无套带白浆嗯呢啊污| 免费男人和女人黄片|