亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Vietnam

Release time:2023-11-13 11:19:13 Hits: Current position: Home > News

This article mainly introduces:

Vietnam hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Vietnam swager cylinder

(Vietnam swager cylinder,produced by Hengyu Hydraulic Cylinder Factory)

swager cylinder are widely used in Vietnam,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed swager cylinder for customers from Vietnam.

Introduction to swager cylinder:

The main role of the swager cylinder: the swager cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the swager cylinder realizes reciprocating motion. The structure of the swager cylinder has three categories: piston swager cylinder, plunger swager cylinder, swing swager cylinder, piston swager cylinder and plunger swager cylinder to achieve reciprocating linear motion, output speed and thrust, swing swager cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the swager cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The swager cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

swager cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the swager cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When the initial action of the swager cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the swager cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

When the piston speed of the swager cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the swager cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

Answers to some questions about swager cylinder:

What's the use of three oil pipes on the cylinder?
The cylinder usually has an upper and lower oil chamber, one is connected to the upper oil chamber, one is connected to the lower oil chamber, sometimes a hydraulic lock will be added, that is, a hydraulic control check valve to prevent accidents when the oil pipe breaks, so the third pipe should be the control oil pipe of the hydraulic control check valve.

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
波多野吉衣吹潮Av| 国产精品熟女视频播放| 美女日比视频播放| 夫妻性生活视频在线直播| 美女骚逼黄色18禁| 久久久久精品无码专区喝奶| 高清无码精品一区二区三区| 熟妇丰满大阴户熟妇啪啪| 欧美男女舔逼舔鸡巴视频| 国产亚洲一区白丝在线观看| 差鸡巴没码在线观看| 美女被大屌操大骚逼| 美女被插b在线观看| 成人毛片一级特黄| 翘臀小穴在线观看| 国产裸模大尺度私拍视频| 波多野吉衣一区在线观看| 国产乱色国产精品免费播放| 一级做a爱过程免费视频俩| 免费黄片视频星空| 天天干天天操天天插| 97人妻精品一区二区三区视频| 你懂的在线中文字幕一区| 免费男人和女人黄片| 日韩高清精品一区有码在线| 国产欧美洲中文字幕床上| 激烈18禁高潮视频免费| 欧美伦禁片在线播放| 日韩一区二区三区国色天香| 鸡巴和逼中国美女| 日韩成人伦理片在线观看| 哈啊慢点不要了视频| 大逼女人污污视频| 精品日本一区二区三区视频播放| 日本黑鸡吧黄色录像| 亚洲一区二区三区四区国产| 激烈18禁高潮视频免费| 大吊肏子宫在线观看| 日本高清不卡一区二区三区| 精品一区二区av天堂色偷偷| 亚洲欧洲综合成人综合网|