亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

500 tons hydraulic press cylinder Sold to Kuwait

Release time:2023-11-12 15:33:44 Hits: Current position: Home > News

This article mainly introduces:

Kuwait hydraulic cylinder,500 tons hydraulic press cylinder manufacturer,500 tons hydraulic press cylinder

Kuwait 500 tons hydraulic press cylinder

(Kuwait 500 tons hydraulic press cylinder,produced by Hengyu Group)

500 tons hydraulic press cylinder are widely used in Kuwait,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed 500 tons hydraulic press cylinder for customers from Kuwait.

Introduction to 500 tons hydraulic press cylinder:

Disassembly 500 tons hydraulic press cylinder: When disassembly 500 tons hydraulic press cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the 500 tons hydraulic press cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the 500 tons hydraulic press cylinder.

We can not just consider the price and ignore the quality when we purchase the 500 tons hydraulic press cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the 500 tons hydraulic press cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the 500 tons hydraulic press cylinder is not required.

When using the 500 tons hydraulic press cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the 500 tons hydraulic press cylinder block. If the 500 tons hydraulic press cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the 500 tons hydraulic press cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the 500 tons hydraulic press cylinder, so that the working efficiency of the 500 tons hydraulic press cylinder is reduced.

Most of the failure of the 500 tons hydraulic press cylinder is because there is a foreign body in the 500 tons hydraulic press cylinder into the failure of the 500 tons hydraulic press cylinder, the most problematic is that it is difficult to determine when the foreign body is into the 500 tons hydraulic press cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about 500 tons hydraulic press cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

How to calculate cylinder pressure?
Hydraulic pressure area of cylinder × hydraulic pressure = output force of cylinder 200mm=20cm 100mm=10cm 15Mpa=150Kg/cm2 Cylinder thrust: 3.14×10×10 area ×150 pressure =47100Kg=47.1t cylinder pulling force: 3.14×(10×10-5×5) Area ×150 pressure =35325Kg=35.325t The above calculation did not consider the resistance of oil return, because you did not provide oil return pressure. But the impact should be small.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
在线无码一区二区三区不卡| 国产日女人视频在线观看| 亚洲欧美国产原创一区二区三区| 美女大鸡操很多水在线看| 精品久久久久中文字幕人| 国产亚洲欧美日韩在线观看一区| 91秦先生全集在线观看| 高颜值情侣鸡巴插插淫叫| 日韩久久奶茶视频| 男生的小鸡鸡插进女生的桃子 里| 日韩精品无码一区二区三区不卡| 国产免费无码一区二区视频无码| 看看美日韩操逼吧| 天美传媒精品1区2区3区| 久久综合久久久久综合大| 女人日比比视频免费| 91偷自产一区二区三区蜜臀| 成人av大全免费一区二区三区| 国产精品久久大屁股白浆| 精品一区二区三区乱码中文字幕| 亚洲av熟妇高潮精品啪啪| 日本人妻与家公的伦理片| 大香蕉操逼小视频| 国产欧美日本韩国一区二区| 白虎嫩穴抠逼高潮| 五月天婷婷一区二区三区久久| 大胸美女被c的嗷嗷叫视频| 捆绑调教白浆一区二区三区| 下载风骚美女想吃大机吧| 国产免费无码一区二区视频无码| 久久久精品亚洲Av| 嗯啊好大好想要视频| 色熟妇人妻久久中文字幕| 少妇被黑人到高潮喷出白浆| 中文字幕 av一区二区| 亚洲精品一区二区精华液| 精品人妻一区二区三区日产乱码| 伊人成人精品在线| 操美女逼逼色逼网| 午夜国产三级一区二区三| 精华欧美一区二区久久久|