亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

cargo elevator hydraulic cylinder Sold to Saudi Arabia

Release time:2023-11-12 15:33:40 Hits: Current position: Home > News

This article mainly introduces:

Saudi Arabia hydraulic cylinder,cargo elevator hydraulic cylinder manufacturer,cargo elevator hydraulic cylinder

Saudi Arabia cargo elevator hydraulic cylinder

(Saudi Arabia cargo elevator hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

cargo elevator hydraulic cylinder are widely used in Saudi Arabia,because of no need for deceleration device,long service life,smooth movement.So our company has designed cargo elevator hydraulic cylinder for customers from Saudi Arabia.

Introduction to cargo elevator hydraulic cylinder:

When the cargo elevator hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the cargo elevator hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil cargo elevator hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical cargo elevator hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the cargo elevator hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

When purchasing the cargo elevator hydraulic cylinder, try to clarify the following parameters of the cargo elevator hydraulic cylinder: A. cargo elevator hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or cargo elevator hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right cargo elevator hydraulic cylinder type can be found accurately and quickly.

When the cargo elevator hydraulic cylinder is in use, ensure that the cargo elevator hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

Because of the slightly complex structure of the buffer cargo elevator hydraulic cylinder, sometimes there will be problems, such as when the cargo elevator hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

Answers to some questions about cargo elevator hydraulic cylinder:

Why should the piston rod of the hydraulic cylinder be so precise? If you hope the cylinder has a long service cycle, then all parts need to be high-precision, not only the piston rod, but also the cylinder, the sealing groove, the surface roughness, the cylinder looks very simple. Any hydraulic factory can produce the cylinder, but the good cylinder is difficult to produce.

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
一级做a爱过程免费视频俩| 美女被插入小穴爆操视频| 大鸡吧干小逼逼视频大全| 国产精品一区二区在线观看91| 亚洲精品自拍偷拍| 操女人大逼视频下载| 大肌巴日小个子女人视频| 国产综合精品一区二区青青| 日本一区二区三区四区五| 在线观看国产黄色| 欧美一区二区高清视频在线观看| 小嫩骚逼操死你视频| 欧美日韩精品视频在线第一区| 国产一区二区三区午夜精品久久| 日本十八禁大骚逼| 快速了解国产一级a爱片| 男人摸女人下面视频| 性一交一乱一乱一区二区| 日韩人妻无码中字一区二区| 看小伙草白女人比的黄片| 女人182毛片a级毛片| 国产一区二区在线观看精品| 亚洲欧美一区二区三区孕妇| 性爱大鸡吧喷水视频| 欧美va精品亚洲va精品| 91性潮久久久久久久久| 亚洲大尺度无码无码专线一区| 欧美精品国产一区二区在线观看| 大鸡巴操饿罗斯女人| 黑人大鸡巴双插美女| 普通话大屌操小穴| 找个日韩操逼的看看| 99草草视频在线精品| 草草久性色av综合av| 欧美大胆a级视频 一本| 亚洲综合极品香蕉久久网| 操鸡巴奶子在线观看| 国产 日韩 亚洲 一区| 国精品午夜福利视频导航| 黑人与日本人妻中文字幕| 青春草在线视频观看|