亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Costa Rica

Release time:2023-11-12 15:32:43 Hits: Current position: Home > News

This article mainly introduces:

Costa Rica hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Costa Rica single rack cylinder

(Costa Rica single rack cylinder,produced by Hengyu Group)

single rack cylinder are widely used in Costa Rica,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed single rack cylinder for customers from Costa Rica.

Introduction to single rack cylinder:

Repair method of small range wear of oil single rack cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

The wear of the hard chromium plating layer of the single rack cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Classification of single rack cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

single rack cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the single rack cylinder head itself is the guide sleeve of the piston rod, the single rack cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the single rack cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Answers to some questions about single rack cylinder:

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产青青操骚货在线观看| 久久久国产精品2020| 日本一区二区在线高清| 巨屌抽插舔阴视频| 女生的鸡鸡色色软件| 国产精品欧美久久久久久| 极品 操 抽插视频| 操逼啊 啊 啊黄色视频| 日本人色频在线看观| 欧美办公室大鸡巴| 非洲大鸡巴操逼黄色录像| 国产精品免费99久久久| 91精品国产综合久久久蜜| 欧美一级淫片免费播放口| 哈啊慢点不要了视频| 国产乱理伦片在线观看夜| 欧美一区二区三区色婷婷月色| 日本一二区视频在线观看| 无码毛片一区二区本码视频| 69国产成人综合久久精| 男生操女生无马赛克免费| 最是人间烟火色在线播放| 精品久久久久五月婷五月| 呦交小u女国产精品99| 精品麻豆国产免费一区二区三区| 夫妻性生活视频在线直播| 国产精品毛片一区视频播| 澳门一区二区免费下线观看| 大鸡巴抽插小骚逼视频免费| 老司机午夜精品视频无码| 日韩精品人妻一区二区免费| 国产日女人视频在线观看| 欧美一区二区三区身体| 美女被插入小穴爆操视频| 欧美精品第15页| 久久久久久久久中文字幕| 男人插女人视频软件| 亚洲av熟妇高潮精品啪啪| 天美传媒精品1区2区3区| 捆绑调教白浆一区二区三区| 亚洲av午夜一区二区|