亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic engineering cylinder Sold to Portugal

Release time:2023-11-12 15:32:35 Hits: Current position: Home > News

This article mainly introduces:

Portugal hydraulic cylinder,hydraulic engineering cylinder manufacturer,hydraulic engineering cylinder

Portugal hydraulic engineering cylinder

(Portugal hydraulic engineering cylinder,produced by Hebei Hengyu company)

hydraulic engineering cylinder are widely used in Portugal,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed hydraulic engineering cylinder for customers from Portugal.

Introduction to hydraulic engineering cylinder:

Because of the slightly complex structure of the buffer hydraulic engineering cylinder, sometimes there will be problems, such as when the hydraulic engineering cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the hydraulic engineering cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

When the hydraulic engineering cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the hydraulic engineering cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil hydraulic engineering cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical hydraulic engineering cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the hydraulic engineering cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the hydraulic engineering cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Answers to some questions about hydraulic engineering cylinder:

There are four cylinders in the front top of the dump truck. When the second cylinder is lifted to half the height, it suddenly falls back more than 30 cm or so, and the cylinder continues to lift.
The problem is the cylinder, the second section of the different strength of the heart. When the oil supply resistance is small, the first out, when the power is not moving, the cylinder needs to be strong, because the second section needs to pop it out after a while when the pressure is large, the oil can not keep up, so it falls back, and the oil continues to keep up.

What does cylinder speed ratio mean?
The speed ratio of the cylinder is the ratio of the reciprocating speed of the piston, equal to the ratio of the rodless cavity area to the roded cavity area.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本乱人伦中文在线播放| 日本公共厕所mmm撒尿| 少妇勾搭外卖员在线观看| 国产裸体视频BBBBB| 抽插肥嫩小穴的视频| AV无码超清破解版流出| 青娱乐极品视觉导航| 欧美一区二区三区四公司| 999久久久国产大美腿| 亚洲国产综合精品 在线 一区| 一区二区三区中文字幕免费在线| 亚洲日韩不卡一区二区三区| 99热这里有精品在线观看| 夜夜嗨av少妇一二三区| 一区二区三区国产l精品欧美| 久久精品男人的天堂av| 欧美一级淫片免费播放口| 中文字幕人妻一区二区三区久久| 国产伦精品一区二区三区视频抖音| 日韩美女一区二区三区香蕉视频| 精品无码国产一区二区三区麻豆| 亚洲综合网伊人中文| 五月天国产成人av在线| 欧美人与动人物A级| 国产老妇伦国产熟女91| 日韩高清精品一区有码在线| 亚洲精品自拍偷拍第一页| 粉色av一区二区三区| 999精品免费视频| 五月天亚洲激情综合av| 少妇勾搭外卖员在线观看| 国产精品久久大屁股白浆| 大男人在线无码直播| 美女的粉嫩小逼视频特写| 偷窥国内肥臀老熟女视频| 女人被躁到高潮嗷嗷叫小| 国产精品欧美久久久久久| 少妇被黑人到高潮喷出白浆| 大鸡巴插入阴道视频| 久久国产亚洲高清| 大鸡巴狂插嫩逼视频|