亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

baling press cylinder Sold to Angola

Release time:2023-11-07 17:48:00 Hits: Current position: Home > News

This article mainly introduces:

Angola hydraulic cylinder,baling press cylinder manufacturer,baling press cylinder

Angola baling press cylinder

(Angola baling press cylinder,produced by Hengyu Hydraulic Co., Ltd)

baling press cylinder are widely used in Angola,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed baling press cylinder for customers from Angola.

Introduction to baling press cylinder:

The wear of the hard chromium plating layer of the baling press cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

The quality of the baling press cylinder can not be ignored in the purchase of the baling press cylinder. The baling press cylinder is the main component of the baling press cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. baling press cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of baling press cylinder is deep hole processing, which has always troubled the processing personnel.

When producing oil baling press cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

baling press cylinder use should try to avoid sealing belt into the baling press cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the baling press cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the baling press cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

Answers to some questions about baling press cylinder:

When the cylinder is tested, why can't the pressure be maintained with the balance valve?
Because the oil into the oil chamber through the hydraulic lock on the control oil circuit through the other side of the spool, the original valve is designed in this way. It locks the circuit after the oil supply circuit loses pressure, on the contrary, if you keep supplying pressure, it is always in the state of opening the other side of the one-way spool. So this valve can't be used in the test.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产 推油 性爱| 中国三级片在线视频| 女人被男人操到高潮视频| 欧美一区二区三区四公司| 喜欢被粗大阴茎插入| 国产精品久久一区二区三区夜色| 一区亚洲免费二区| 真人作爱免费视频| 日韩午夜资源在线观看| 午夜性刺激在线视频免费| 中文字幕国产精品一区二区三区| 粉嫩小穴被大鸡巴操视频在线观看| 欧美精品视频在线| 99久久99久久精品视频| 色逼色逼色逼色逼色逼色| 鸡巴操美女小穴羞羞视频| 美女最骚逼逼视频| 成人国产亚洲精品一区二| 午夜国产精品午夜福利网| 女同舔我下面直流水| 国产高欧美性情一线在线| 日本一区二区三区四区五| 无码中文字幕免费一区二区三区| 黄色录像片操大逼的| 国产亚洲欧美中文日韩| 女人的骚逼免费视频| 挺进绝色邻居的紧窄小肉| 白丝袜子宫啊啊啊不要了| 久久久国产了楼凤| 日本高清一区二区三区水蜜桃| 正在播放老熟女人与小伙| 阴茎大头插少妇蜜穴视频| 久久久精品亚洲Av| 欧美精品性做久久久久久| 国产精品一区二区三区在线视| 91麻豆精品福利在线观看| 欧美日韩一区精品一区精品| 国产免费无码一区二区视频无码| 国产精品无码一二区免费| 免费看澡美女逼视频看看| 国产熟女露脸普通话对白|