亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

automobile tailboard cylinder Sold to Tanzania

Release time:2023-11-12 15:31:41 Hits: Current position: Home > News

This article mainly introduces:

Tanzania hydraulic cylinder,automobile tailboard cylinder manufacturer,automobile tailboard cylinder

Tanzania automobile tailboard cylinder

(Tanzania automobile tailboard cylinder,produced by Hebei Hengyu company)

automobile tailboard cylinder are widely used in Tanzania,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed automobile tailboard cylinder for customers from Tanzania.

Introduction to automobile tailboard cylinder:

When installing the automobile tailboard cylinder pipe, the pipe should be cleaned after installation, and should not pass through the automobile tailboard cylinder block, and the by-pass pipe must be installed in front of the oil port of the automobile tailboard cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the automobile tailboard cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the automobile tailboard cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

If air enters the hydraulic system, the automobile tailboard cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the automobile tailboard cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

How to determine the working pressure of the automobile tailboard cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, automobile tailboard cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about automobile tailboard cylinder:

Structural characteristics of the plunger cylinder? (1) The plunger hydraulic cylinder is a single-acting hydraulic cylinder, which can only move in one direction by hydraulic pressure, and the return trip of the plunger depends on other external forces or the weight of the plunger; (2) The plunger is only supported by the cylinder liner and is not in contact with the cylinder liner, so the cylinder liner is easy to process, so it is suitable for long stroke hydraulic cylinder; (3) the total pressure of the plunger during work, so it must have sufficient stiffness; (4) The weight of the plunger is often large, and it is easy to sag due to its own weight when placed horizontally, resulting in wear of the seals and guide side, so its vertical use is more favorable.

Where is the tension cylinder used in the excavator?
Get off the inside of the frame, behind the guide wheel (steering wheel, guide wheel). Disassemble the track and take the guide wheel out to see the tensioning cylinder (track spring).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品国产精黄 | 亚洲国产国产综合一区首页| 国产精品国产三级国| 国产亚洲欧美日韩在线观看一区| 农村胖肥胖女人操逼视频| 国产精品不只是精品| 美女玩奶子和鸡巴| 久久国产亚洲高清| 国产精品一区二区在线观看91| 97超级免费视频在线观看| 亚洲欧洲精品无码久久久| 少妇勾搭外卖员在线观看| 中日美女毛5片一区二区三区| 大鸡巴抽插小穴色虐视频| 国产精品亚洲一区二区三区下载| 奇米一区二区三区视频在线观看| 男人大鸡巴操小鲜肉视频| 人人摸人 人干人人草操| 好爽又高潮了毛片在线看| 日韩久久中文字幕| 好嗨哟直播看片在线观看| 午夜色大片在线免费观看| 狠狠干无码日韩AV| 欧美日本欧美日本区一区二| 99久久九九爱精品国产| 色噜噜人妻丝袜中文字幕| 90岁肥老奶奶毛毛外套| 女人被男人操到高潮视频| 丰满少妇被强入在线观看| 欧美精品日韩精品中文字幕| 日韩欧美人妻综合| 九九视频这里只有精品| 大波美女被插的好爽| 国产精品亚洲一区二区三区极品| 国产欧美一二区不卡视频| 无码毛片一区二区本码视频| 极品美女销魂一区二区三区| 一区二区三区av精品| 国产精品免费第一区二区| 粗大长内射女人视频| 日韩精品无码一区二区三区不卡|