亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

road paving machine hydraulic cylinder Sold to Tunisia

Release time:2023-11-12 15:31:24 Hits: Current position: Home > News

This article mainly introduces:

Tunisia hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

Tunisia road paving machine hydraulic cylinder

(Tunisia road paving machine hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

road paving machine hydraulic cylinder are widely used in Tunisia,because of powerful torque,excellent temperature resistance,no transmission clearance.So our company has designed road paving machine hydraulic cylinder for customers from Tunisia.

Introduction to road paving machine hydraulic cylinder:

The difference between the plunger road paving machine hydraulic cylinder and the piston road paving machine hydraulic cylinder is that the piston in the road paving machine hydraulic cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type road paving machine hydraulic cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the road paving machine hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

road paving machine hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the road paving machine hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

road paving machine hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

Answers to some questions about road paving machine hydraulic cylinder:

What steel pipe does hydraulic cylinder use? This problem is very general. Carbon steel pipe or ordinary seamless steel pipe are all ok, but then there are rolling, quilting, heat treatment and other steps, and the requirements are different, the wall thickness is different, the material is different. It depends on the circumstances.

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中日韩国内精品视频| 国产成人精品区在线观看| 大波美女被插的好爽| 啊灬啊别停灬用力啊男男在线观看| 天堂无码不卡av| 青娱乐欧美性爱视频| 中国毛茸茸的操逼| 大香蕉大香蕉大香蕉大香| 亚洲一区二区三区大胆视频| 国产精品免费第一区二区| 午夜性福福利视频一区二区三区| 中文字幕一区二区 在线| 一级风流国产片a级| 骚逼嫩鸡巴喷水视频| 色综合色狠狠天天综合色| 日韩人妻无码中字一区二区| 精品免费久久久久久久久| 亚洲精品国产人久久| 大鸡插骚货人人色| 骚穴手机在线视频| 留学生美女被大黑屌猛戳| 国产亂倫近親相姦| 男生插女生下面流出白色精液视频| 白虎美女被大基吧操| 91麻豆精品福利在线观看| 一区二区三区四区五六区| 国产精品一区二区日本欧美| 国产熟女露脸普通话对白| 日韩 欧美 一区 二区三区| 国产精品亚洲一区二区三区下载| 亚洲AV无码一区二区三区系列| 顶的速度越来越快越| 亚洲美女后入在线播放| 日本老熟妇毛茸茸| 开心五月播五月亚洲第一| 免看一级a一片成人欧美| 中日美女毛5片一区二区三区| 亚洲av午夜一区二区| 大鸡吧干小逼逼视频大全| 亚洲色欲久久久久综合网| 操女人大逼视频下载|