亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

double acting cylinder Sold to Ethiopia

Release time:2023-11-12 15:30:37 Hits: Current position: Home > News

This article mainly introduces:

Ethiopia hydraulic cylinder,double acting cylinder manufacturer,double acting cylinder

Ethiopia double acting cylinder

(Ethiopia double acting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

double acting cylinder are widely used in Ethiopia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed double acting cylinder for customers from Ethiopia.

Introduction to double acting cylinder:

The wear of the hard chromium plating layer of the double acting cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

After chrome plating of the piston rod of the double acting cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The repair method of the double acting cylinder: the repair of the double acting cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The double acting cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the double acting cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The double acting cylinder is basically composed of double acting cylinder and double acting cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

Answers to some questions about double acting cylinder:

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
999精品免费视频| 国产精品午夜小视频观看| 性爱大鸡吧喷水视频| 几把日逼嗯嗯视频| 老司机精品成人无码AV| 黑人大吊又操又添| 中文字幕乱码人妻一区二区三区| 鸡巴操骚逼视频播放| 免费观看的黄视频一级国产| 日本人色频在线看观| 骚女人被大吊干视‘| 欧洲老妇人操大逼| 天天躁久久躁中文字字幕| 精品久久久久亚洲中文字幕| 欧美尤物操逼毛茸茸真爽| 把美女日到高潮喷水视频| 高颜值情侣鸡巴插插淫叫| 亚洲一区二区三区大胆视频| 奇米一区二区三区视频在线观看| 性一交一子一伦一乱| 久久国产精品成人18p| 美女日比视频播放| 99视频在线看免费视频| 男人几把操女人嫩穴| 东京热无码AV一区二区三区| 亚洲天堂成年人在线视频| 国产精品一区二区三区在线视| 高颜值美女视频在线观看| 大鸡巴操逼视频免费| 一区二区在线不卡| 人人摸人 人干人人草操| 国产精品碰碰现在自| 天天干天天操天天插| 美女人的逼免费观看| 日韩高清精品一区有码在线| 亚洲av一区二区在线看| 97超视频免费在线观看| 亚洲Av无码专区一区二区三区| 黑丝美女被操哭边操边尿| 色999日韩自偷自拍美女| 三男狂插小穴穴视频|