亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

punch machine hydraulic cylinder Sold to Switzerland

Release time:2023-11-12 15:30:31 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,punch machine hydraulic cylinder manufacturer,punch machine hydraulic cylinder

Switzerland punch machine hydraulic cylinder

(Switzerland punch machine hydraulic cylinder,produced by Hengyu Group)

punch machine hydraulic cylinder are widely used in Switzerland,because of smooth movement,no need for deceleration device,long service life.So our company has designed punch machine hydraulic cylinder for customers from Switzerland.

Introduction to punch machine hydraulic cylinder:

punch machine hydraulic cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards punch machine hydraulic cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the punch machine hydraulic cylinder guide is determined by the length of the stroke. Check the strength of punch machine hydraulic cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the punch machine hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Do not regularly check the damage of the chrome layer of the punch machine hydraulic cylinder: completely extend the punch machine hydraulic cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the punch machine hydraulic cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the punch machine hydraulic cylinder seal. Welding slag is strictly prohibited on the surface of the punch machine hydraulic cylinder.

Piston punch machine hydraulic cylinder is widely used in hydraulic transmission. When the punch machine hydraulic cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the punch machine hydraulic cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the punch machine hydraulic cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

Answers to some questions about punch machine hydraulic cylinder:

In hydraulic equipment, is the motor power related to the cylinder pressure holding time?
Irrelevant. The motor only drives the plunger in the hydraulic cylinder of the oil pump to extend out, and stops when the set pressure is reached; The length of the pressure holding time is related to the sealing degree of the hydraulic cylinder and the solenoid valve.

How to distinguish large cavity and small cavity of excavator rod cylinder ?
Single rod piston cylinder is a form of cylinder that is used relatively most, and the boom, bucket, dozer shovel cylinder are all in this form. Among them, the rodless cavity is also called the large cavity, and the rodless cavity is also called the small cavity. Therefore, the cylinder cavity on the side with the exposed piston rod is the small cavity, and the cylinder cavity on the side without the exposed rod is the large cavity.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕最新在线资源| 中文字幕亚洲一区巨区| 亚洲精品伦理一区二区三区青春| 蜜臀av国产精品久久久久| 欧美精品精品一区乱| 欧美日韩一区二区中文字幕| 在线播放亚洲欧美日韩| 国产69精品久久久久久老妇| 午夜福利国产观看视频1| 接下来开始上伦理课免费观看| 四虎国产精品成人免费久久| 国产三级黄色片观看| 国产精品熟女高潮久久99| 久久精一区二区三区| 亚洲一区二区三区中文字幕手机在线| 国产精品久久久久久久久三级| 国产精品久久久久99999| 91久久久久人妻精品专区| 精品久久久久久久久久中文幕| 在线无码中文强乱爆乳系列| 日韩一区二区三区日韩精品| 久久久久精品欧美日韩精品| 欧美成人3p视频在线观看| 亚洲中文无无码第21页| 久久精品一本无码免费| 国产av一区最新精品麻豆| 1024欧美一区二区三区人妻| 国产精品青青青高清在线观看| 午夜无码精品一区二区三区| 中文字幕亚洲一区巨区| 911国产精品视频| 国产精品久久久久99999| 久久久久久久久久久极品| 日本午夜免费福利视频| 欧美日韩一区二区中文字幕| 国产精品久久久久久久久三级| av网址在线播放大全| 亚洲欧美成在线观看| 国产精品美女作爱视频| 国产精品久久久久久久久久一区| 国产精品国语对白在线观看|