亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

cylinder with sensor Sold to Switzerland

Release time:2023-11-12 15:30:22 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,cylinder with sensor manufacturer,cylinder with sensor

Switzerland cylinder with sensor

(Switzerland cylinder with sensor,produced by Hengyu Group)

cylinder with sensor are widely used in Switzerland,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed cylinder with sensor for customers from Switzerland.

Introduction to cylinder with sensor:

When the cylinder with sensor is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the cylinder with sensor seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

When the cylinder with sensor is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the cylinder with sensor is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

When the cylinder with sensor needs to be stored for a period of time, please follow the recommended methods: The cylinder with sensor should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the cylinder with sensor from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil cylinder with sensor should not be in direct contact with water vapor for a long time. The cylinder with sensor should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the cylinder with sensor and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the cylinder with sensor Before working, the cylinder with sensor must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the cylinder with sensor before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

There are some honeycomb holes in the inner wall of the cylinder with sensor, piston or piston rod surface. How is this formed? When we repair the cylinder with sensor, we can see that there are some honeycomb holes on the inner wall of the cylinder with sensor, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the cylinder with sensor is targeted to prevent. Is very necessary.

Answers to some questions about cylinder with sensor:

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

Need to buy a hydraulic cylinder, now only know that the pressure needs to be between 20t and 50t. Two-way travel, how to determine the type of cylinder?
Important parameters of the cylinder: cylinder diameter, stroke, use pressure. First, the system pressure must be determined according to the precision of the operation of the application equipment, and the cylinder diameter can be determined by the force and system pressure. Then, according to how the equipment and the cylinder are installed and connected, determine the installation method of the cylinder and then determine the specific installation size, the size of the oil port, whether the buffer is needed and other details.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
帅哥大鸡巴操美女| 免费黄色 操逼视频| 日本不卡免费一区二区视频| 韩国女主播一区二区视频| 操纯欲女生小穴视频| 热精品韩国毛久久久久久| 亚洲一区二区女同性恋免费看| 91孕妇精品一区二区三区| 精品一二三四区中文字幕| 欧美日本欧美日本区一区二| 国产精品粉嫩懂色av| 精品久久久久中文字幕人| 男生插女生下面流出白色精液视频| 国产污污污在线观看视频| 男人草女人的视频免费看| 喜欢被粗大阴茎插入| 国产成人亚洲欧美久久| 日韩乱码一区二区三区中文字幕| 中文有码无码人妻在线看| 毛片日产av一区二区三区四区| 日韩精品一区av在线| 中文字幕av一区二区三区蜜桃| 日韩 中文字幕在线最新| 成人区久久精品一区二区| ai换脸久久一区二区亚洲av| 伊人久久丁香色婷婷啪啪| 免费看澡美女逼视频看看| 几把日逼嗯嗯视频| 午夜精品福利一区二区三区蜜桃p| 国产欧美洲中文字幕床上| 国产精品白浆一区二区三区| 欧美精品国产一区二区在线观看| 国产成人亚洲欧美久久| 在线观看国产日韩欧美一区二区| 日本亚洲免费不卡| 熟妇好大好深好爽| 抽插肥嫩小穴的视频| 日韩成人伦理片在线观看| 狠狠干无码日韩AV| 国产高清第一区第二区第一页| 天天爽夜夜爽夜夜爽一区|