亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Peru

Release time:2023-11-12 15:30:11 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Peru servo cylinder

(Peru servo cylinder,produced by Hengyu Group)

servo cylinder are widely used in Peru,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed servo cylinder for customers from Peru.

Introduction to servo cylinder:

The servo cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

servo cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the servo cylinder is placed for a period of time, the servo cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

When the servo cylinder is customized, if there are high requirements for the quality of the servo cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the servo cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the servo cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When the initial action of the servo cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the servo cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Answers to some questions about servo cylinder:

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
男的日女生批网页| 粗大长内射女人视频| 美女嫩逼插进大屌| 欧美伦禁片在线播放| 男人摸女人下面视频| 国产精品免费99久久久| 久久99国产中文| 国内精品久久久久精品97| 爱男爽高潮鸡穴视频| 美国毛片亚洲社区成人看| 小穴抽插流水视频| 久久久中文字幕在线视频| 亚洲欧洲精品无码久久久| 你懂的在线中文字幕一区| 精品v欧洲高清欧美| 开心五月播五月亚洲第一| 亚洲欧洲精品无码久久久| 96精品久久久久久蜜臀浪| 久久国产高清波多野结衣| 亚洲福利小视频在线观看| 蜜桃av噜噜一区二区三区免费| 大鸡巴射在穴穴里的视频| 日韩午夜精品中文字幕| 亚洲欧美日韩另类| 鸡巴操骚逼视频播放| 亚洲高清中文字幕一区二区三区| 综合欧美日韩一区二区三区| 一级美女插逼百度| 大鸡巴狂插嫩逼视频| 国产精品免费久久久久久| 老色鬼精品视频二区三区| 美女让我插她的骚逼| 国产成人无码AV一区二区三区| 亚洲国产一区二区不卡在线资源| 久久久久人妻一区精品加勒比| 亚洲国产精品伦理在线看| 美国女人抠插bbb| 日本美女阴户射尿| 粉嫩小穴被大鸡巴操视频在线观看| 一级e片在线观看| 亚洲狠狠插狠狠搞狠狠摸|