亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift lift cylinder Sold to Bahrain

Release time:2023-11-12 15:30:07 Hits: Current position: Home > News

This article mainly introduces:

Bahrain hydraulic cylinder,forklift lift cylinder manufacturer,forklift lift cylinder

Bahrain forklift lift cylinder

(Bahrain forklift lift cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift lift cylinder are widely used in Bahrain,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed forklift lift cylinder for customers from Bahrain.

Introduction to forklift lift cylinder:

The repair method of the forklift lift cylinder: the repair of the forklift lift cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The commonly used buffer structure of the forklift lift cylinder is composed of a piston boss and a forklift lift cylinder head groove. When the piston moves close to the forklift lift cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

The cavitation of the forklift lift cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the forklift lift cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

In use, the forklift lift cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the forklift lift cylinder.

Answers to some questions about forklift lift cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

How to distinguish the bucket cylinder from the bucket rod cylinder?
It can be distinguished according to its installation and connection: one end of the bucket cylinder is connected with the bucket; The rod cylinder is not connected to the bucket. The bucket refers to the bucket installed on the excavator. According to the working mode, it is divided into backhoe bucket and shovel bucket, the backhoe bucket is commonly used. The boom and bucket rod are working device of the excavator, usually called the big arm and the forearm, which are mainly used to control the digging and loading of the bucket. The arm connected to the frame is longer, so it is commonly known as the big arm, and its term is called the boom. The arms connected to the digging bucket are smaller, so they are commonly known as the lower arms, and the term is called the bucket rod, so they are commonly known as the big lower arms.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
老湿机69福免费破解版| 无码成人一区二区| 大黑屌爆操日本女人| 日本人色频在线看观| 久久久久久国产A免费观看| 欧美 日本 亚洲 国产| 日韩av一区二区高清不卡| 老司机精品成人无码AV| 大鸡吧插美女嫩逼| 99热这里只有精品98| 俩男人插下面的视频| 中文字幕亚洲欧美精品一区二区| 日本一区二区三区高潮喷吹| 久久一区二区三区精华液介绍| 日本高清一区二区三区在线观看| 两人爽爽爽无码免费视频| 国产午夜爽爽爽男女免费动漫AV| 大鸡巴抽插小穴色虐视频| 无码视频在线观看| 女教师色色天天免费播放| 色婷婷五月综合久久| 三级无码日B视频| 国产精品一区二区日本欧美| 国产高清在线观看一区二区三区| AV无码超清破解版流出| 大鸡巴插入阴道视频| 彩虹网免费视频在线观看| 亚洲日韩不卡一区二区三区| 欧美日韩国产欧美| 国产欧美日韩一区二区在线观看| 白丝袜子宫啊啊啊不要了| 大胸美女被c的嗷嗷叫视频| 欧美一区二区三区久久国产精品| 日国产精品1卡二卡三卡| 亚洲大尺度无码无码专线一区| 国产亚洲一区二区手机在线观看| 日本免费无码一区二区到五区| 欧美精品视频在线| 男女边吃奶边做边爱视频| 天堂丝袜人妻中文字幕在线| 国产精品自在自线。|