亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

lifting platform cylinder Sold to Switzerland

Release time:2023-11-12 15:28:53 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,lifting platform cylinder manufacturer,lifting platform cylinder

Switzerland lifting platform cylinder

(Switzerland lifting platform cylinder,produced by Hengyu Hydraulic Co., Ltd)

lifting platform cylinder are widely used in Switzerland,because of no need for deceleration device,long service life,smooth movement.So our company has designed lifting platform cylinder for customers from Switzerland.

Introduction to lifting platform cylinder:

If the piston rod and lifting platform cylinder are stuck or the lifting platform cylinder is blocked, at this time, no matter how to operate, the lifting platform cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the lifting platform cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

In the process of using the lifting platform cylinder, sometimes such a problem will occur, the lifting platform cylinder can not act immediately after the instruction of the lifting platform cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil lifting platform cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

The machining accuracy of the lifting platform cylinder depends on the level of equipment, production technology and testing means. lifting platform cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

lifting platform cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the lifting platform cylinder is placed for a period of time, the lifting platform cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

Answers to some questions about lifting platform cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品国产Av无码久久久一区二区| 中文字幕欧美人妻在线| 国产欧美一二区不卡视频| 永久性日韩无码视频| 国产欧美一区二区精品久久久| 日韩av午夜福利在线观看| 日本亚洲欧洲一区二区| 国产精品视频一区二区三区分享| 国产精品无码一二区免费| 色噜噜在线一区二区三区| 乱伦美女小骚货视频| 老狼精品卡1卡2卡3网| 欧美在线A片一区二区三区| 在线免费看污视频| 中文字幕亚洲欧美精品一区二区| 大香蕉尹人97超级视频| 91性潮久久久久久久久| 尤物网三级在线观看| 伊人成人精品在线| 操逼操的翻白眼视频| 在线12萝自慰喷水| 国产一区二区三区 韩国女主播| 男人透女人视频短篇| 丝袜片一区二区三区四区五区| 久久精品国产亚洲av伦理| 色欲精品一区二区三区AV| 天天免费的无码AV| 一区二区国产欧美日韩无| 猛哥操女人B视频| 被公侵犯人妻少妇一区二区三区| 美女人的逼免费观看| 大香蕉操逼小视频| 女人被男人躁爽色欲国产| 国产精品三二一免费| 精品一区二区av天堂色偷偷| 日韩欧美一级特黄大片欧| 91啪国线自产2019| 美国大鸡巴操逼视频| 成人高清在线播放一区二区三区| 色哟哟精品视频一区二区| 波多野吉衣一区在线观看|