亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic booster cylinder Sold to Bulgaria

Release time:2023-11-12 15:28:43 Hits: Current position: Home > News

This article mainly introduces:

Bulgaria hydraulic cylinder,hydraulic booster cylinder manufacturer,hydraulic booster cylinder

Bulgaria hydraulic booster cylinder

(Bulgaria hydraulic booster cylinder,produced by Hengyu Hydraulic Co., Ltd)

hydraulic booster cylinder are widely used in Bulgaria,because of no need for deceleration device,long service life,smooth movement.So our company has designed hydraulic booster cylinder for customers from Bulgaria.

Introduction to hydraulic booster cylinder:

Because of the slightly complex structure of the buffer hydraulic booster cylinder, sometimes there will be problems, such as when the hydraulic booster cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

The commonly used buffer structure of the hydraulic booster cylinder is composed of a piston boss and a hydraulic booster cylinder head groove. When the piston moves close to the hydraulic booster cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

When the hydraulic booster cylinder needs to be stored for a period of time, please follow the recommended methods: The hydraulic booster cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the hydraulic booster cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil hydraulic booster cylinder should not be in direct contact with water vapor for a long time. The hydraulic booster cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the hydraulic booster cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the hydraulic booster cylinder Before working, the hydraulic booster cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the hydraulic booster cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

How the cavitation of the hydraulic booster cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the hydraulic booster cylinder, resulting in corrosive damage to the parts.

Answers to some questions about hydraulic booster cylinder:

How to control the speed of the cylinder?
High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.

What is the material of the cylinder support ring?
Generally, it is polytetrafluoroethylene doped with copper powder, or polyformaldehyde, and copper sleeves, there are also nylon, resin and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品日本一区二区三区视频播放| 日韩在线视频不卡一区二区三区| 日本精品久久人妻一区二区三区| 大香蕉尹人97超级视频| 国产精品自在自线。| 亚洲精品精品精国产| 天堂丝袜人妻中文字幕在线| 春宵福利导航91| 久久久久久亚洲精品首页| 大鸡巴操大屁股美女视频| 中文字幕在线视频一区二区| 欧美一区二区三区刘玥| 男人扒开女人腿狂躁免费| 欧美 日韩 国产 自拍| 国内精品久久久久精品97| 可以免费看污污片的软件| 欧美成人精品一区二区免费看| 性一乱一交一免费看视频| 99精品欧美一区二区三区喷胶| 国产精品毛片一区视频播| 99视频在线看免费视频| 91久久高清国语自产拍| 国产精品亚洲一区二区三区极品| 中文字幕一区二区 在线| 精品一区二区av天堂色偷偷| 中文字幕精品字幕一区二区三区| 午夜性刺激在线视频免费| 中文字幕在线资源第一页| 午夜性无码视频在线播放| 精品v欧洲高清欧美| 18岁美女破处在线观看| 午夜性福福利视频一区二区三区| 九九视频这里只有精品| 精品精品国产一区二区性色av| 国产精品亚洲一区二区三区极品| 看看美日韩操逼吧| 日韩欧美一区二三区风间由美| 亚洲国产精品伦理在线看| 久久久久亚洲精品无码系列| 冷色系的发色有哪些颜色| 国产女主播喷出白浆视频|