亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

press machine hydraulic cylinder Sold to Indonesia

Release time:2023-11-12 15:28:33 Hits: Current position: Home > News

This article mainly introduces:

Indonesia hydraulic cylinder,press machine hydraulic cylinder manufacturer,press machine hydraulic cylinder

Indonesia press machine hydraulic cylinder

(Indonesia press machine hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

press machine hydraulic cylinder are widely used in Indonesia,because of long service life,smooth movement,high work efficiency.So our company has designed press machine hydraulic cylinder for customers from Indonesia.

Introduction to press machine hydraulic cylinder:

The press machine hydraulic cylinder should be vented: when the press machine hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the press machine hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the press machine hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the press machine hydraulic cylinder, the oil is best entered and discharged from the highest point of the press machine hydraulic cylinder. press machine hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

How the cavitation of the press machine hydraulic cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the press machine hydraulic cylinder, resulting in corrosive damage to the parts.

When installing the press machine hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the press machine hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the press machine hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the press machine hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the press machine hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

The meaning of the press machine hydraulic cylinder model marked by the press machine hydraulic cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the press machine hydraulic cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the press machine hydraulic cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

Answers to some questions about press machine hydraulic cylinder:

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

Why is the cylinder not in place when the concrete pump truck changes the piston?
When the concrete pump truck changes the piston, the cylinder is not in place mainly because the transfer oil connecting the two cylinders is not completely drained. Sany and Zhonglian have a piston return switch, which can be used to back the piston to the cleaning tank. The elephant is equipped with a stop valve at the bottom of the oil cylinder, usually in the closed state, when opened, the piston can be returned to the cleaning tank, remember to close the valve after the piston is updated.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品麻豆亚洲欧美| 欧美大鸡巴插入骚b| 欧美精品第一区二区三区| 大男人在线无码直播| 狠狠色伊人亚洲综合成人| 久久久久黑人强伦姧人妻| 国产精品不只是精品| 美女呻吟翘臀后进爆白浆| 看看美日韩操逼吧| 色999日韩自偷自拍美女| 欧美日韩在线成人| 在线看免费无码a片视频| 久久久五月性色视频| 亚洲高清中文字幕一区二区三区| 肏亚洲女人小骚逼| 日韩激情视频在线看免费| 日国产精品1卡二卡三卡| 制服丝袜国产在线第一页| 玖玖资源站无码专区| 国产在线中文字幕一区二区三区| 中国美女操逼的视频| 欧美精品第一区二区三区| 美女主播被操流水| 久久综合日韩亚洲精品色| 91精品国产剧情欧美一区二区| 从后面狠狠的干白嫩少妇| 日韩av一区二区高清不卡| 国产精品三二一免费| 欧美 日韩 激情 在线| 大鸡巴操大屁股美女视频| 99草草视频在线精品| 3色w九九久久男人皇宫宕| 国产欧美日韩一区二区在线观看| 亚洲av一区二区在线看| 成人av大全免费一区二区三区| 一区二区三区中文欧美| 国产一级第一级毛片| 激情亚洲人妻精品| 亚洲一区二区三区大胆视频| 天天爽夜夜爽夜夜爽一区| 国产一区二区三区在线观|