亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Puerto Rico

Release time:2023-11-12 15:27:56 Hits: Current position: Home > News

This article mainly introduces:

Puerto Rico hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Puerto Rico steering power cylinder

(Puerto Rico steering power cylinder,produced by Hengyu Hydraulic Cylinder Factory)

steering power cylinder are widely used in Puerto Rico,because of long service life,smooth movement,high work efficiency.So our company has designed steering power cylinder for customers from Puerto Rico.

Introduction to steering power cylinder:

The "O" ring can be used as an auxiliary seal inside the steering power cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the steering power cylinder, and can be completely sealed.

After the steering power cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

If the piston rod and steering power cylinder are stuck or the steering power cylinder is blocked, at this time, no matter how to operate, the steering power cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the steering power cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

How the cavitation of the steering power cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the steering power cylinder, resulting in corrosive damage to the parts.

Answers to some questions about steering power cylinder:

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

What does the maximum output force of the cylinder piston mean?
The maximum output of the cylinder is related to the pressure of the hydraulic system that you link to the cylinder. For example, the rated maximum output thrust of the MOB 50 cylinder is 1.3 tons and the rated pressure is 7Mpa. That is, when the input hydraulic oil pressure of the cylinder reaches 7Mpa, the maximum output thrust of the cylinder is only 0.98 tons. When the input hydraulic pressure is only 5Mpa, the maximum output thrust of the cylinder is 1.3 tons. Because the pressure of the cylinder limit is only 7Mpa, if the oil pressure of the input system exceeds 7Mpa, the cylinder can not withstand the pressure burst, and it is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产午夜久久精品一区四虎| 呦交小u女国产精品99| 欧美大胆a级视频 一本| 黄色日女人逼视频| 潮中文字幕在线观看| 中文字幕亚洲精品女同一页| 伊人久久综合无码成人网| 性色av少妇一区二区三区多人| 喜欢被粗大阴茎插入| 午夜理论理论亚洲激情| 可以免费看污污片的软件| 日韩免费一级a毛片在线播放一级| 欧美日韩一区精品一区精品| 欧美一区二区三区刘玥| 2021国产一区二区岛国| 性一交一子一伦一乱| 国产精品三级一区二区| 亚洲av熟妇高潮精品啪啪| 青娱乐欧美性爱视频| 欧美亚洲干妞内射| 久久精精品久久久久噜噜| 在线12萝自慰喷水| 成人 在线 欧美 日韩| 欧美 日韩 亚洲 熟女| 粉嫩小穴被大鸡巴操视频在线观看| 外国处女BB视频| 操女人大逼视频下载| 欧美国产综合日韩一区二区| 快速了解国产一级a爱片| 添女人荫道口视频| 中文字幕在线视频一区二区| 美国业余自由摘花管| 久久久18禁一区二区网| 九九视频精品只有这里有| 夫妻性生活在线免费视频| 96精品久久久久久蜜臀浪| 日韩视频在线网页| 高颜值情侣鸡巴插插淫叫| 丝袜片一区二区三区四区五区| 成人av大全免费一区二区三区| 骚逼少妇被巨根爆插|