亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Azerbaijan

Release time:2023-11-12 15:27:32 Hits: Current position: Home > News

This article mainly introduces:

Azerbaijan hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Azerbaijan servo hydraulic cylinder

(Azerbaijan servo hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

servo hydraulic cylinder are widely used in Azerbaijan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed servo hydraulic cylinder for customers from Azerbaijan.

Introduction to servo hydraulic cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the servo hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The definition of the minimum stable speed refers to the minimum movement speed of the servo hydraulic cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the servo hydraulic cylinder that undertakes different work has different requirements for the minimum stable speed.

After chrome plating of the piston rod of the servo hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The difference between the integral servo hydraulic cylinder and the split servo hydraulic cylinder: The integral servo hydraulic cylinder and the split servo hydraulic cylinder in the servo hydraulic cylinder are two different servo hydraulic cylinders, and they are very different. The whole servo hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split servo hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and servo hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

Answers to some questions about servo hydraulic cylinder:

How to disassemble the cylinder?
Generally speaking, it is not difficult to disassemble the hydraulic cylinder, as long as you are careful, but you often encounter some small trouble in the disassembly process, because the disassembly process is not correct. In fact, this can be avoided, as long as you follow below points. 1. Before removing the hydraulic cylinder, the hydraulic circuit should be relieved of pressure, otherwise, when the oil pipe connected with the cylinder is loosened, the high-pressure oil in the circuit will be rapidly ejected. When the hydraulic pressure comes back, the handwheel or pressure regulating screw at the relief valve should be loosened first, so that the pressure oil is unloaded, and then the power supply or power source is cut off, so that the hydraulic device stops running. 2. Disassembly should prevent damage to the top thread of the piston rod, the oil thread and the chrome layer on the piston rod surface.

Does the excavator use a hydraulic cylinder?
First, construction machinery is generally a hydraulic cylinder. Second, hydraulic transmission equipment is usually composed of four components, power, execution, control and auxiliary. And the hydraulic cylinder as a linear reciprocating motion or less than 360. Reciprocating motion of the hydraulic mechanism, simple structure, reliable work, is also widely used in the hydraulic system of the main actuator, it is the prime mover in the form of mechanical energy to drive the hydraulic pump produced by the liquid pressure energy, and then can be directly driven load for reciprocating movement or less than 360.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品一区二区日本欧美| 另类 专区 综合 中文| 国产亚洲一区二区手机在线观看| 国产精品视频一区二区三区八戒| 高颜值情侣鸡巴插插淫叫| 日韩免费一级a毛片在线播放一级| 久久高清中文字幕第一页| 日韩av大片一区二区三区| 操我好舒服用力视频| 久久综合娱乐中文网| 大黑鸡巴操模特骚B| 国产精品亚洲综合av| 无码av一区二区大桥久未| 日韩美女一区二区三区香蕉视频| 日韩欧美综合一二三区| 日韩欧美一级特黄大片欧| 中文字幕人妻一区二区三区人妻| 伊人久久久久久久久香港| 男插女下面高潮视频| 美女麻豆颜色光屁股眼子| 夜色成人免费观看| 日韩av午夜福利在线观看| 鸡巴操美女小穴羞羞视频| 大鸡巴操逼 公司| 日本黄色美女射精| 中文字幕乱码一区二区三区麻豆| 黄色av成年人在线观看| 中国三级片在线视频| 91精品国产剧情欧美一区二区| 亚洲乱熟女一区二区三区| 婷婷6月天丁香综合在线| 啊啊啊啊大鸡巴操我视频| 三级片成人京东热五月天| 伊人网在线视频观看| 无码中文字幕免费一区二区三区| 又大黄又硬又爽免费视频| 亚洲欧美一区二区三区孕妇| 可以免费看黄的香蕉视频| 国产乱色国产精品免费播放| 国产午夜福利视频第三区| 在线观看免费视频a v|