亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

folding machine cylinder Sold to Sri Lanka

Release time:2023-11-12 15:27:19 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,folding machine cylinder manufacturer,folding machine cylinder

Sri Lanka folding machine cylinder

(Sri Lanka folding machine cylinder,produced by Hebei Hengyu company)

folding machine cylinder are widely used in Sri Lanka,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed folding machine cylinder for customers from Sri Lanka.

Introduction to folding machine cylinder:

Factors that should be considered when selecting the oil seal in the folding machine cylinder: some specific factors should be taken into account when selecting the oil seal in the folding machine cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: folding machine cylinder diameter, piston rod diameter, piston rod and piston groove size, folding machine cylinder working pressure, folding machine cylinder movement speed, hydraulic system oil temperature and folding machine cylinder working environment.

The internal leakage of the folding machine cylinder should be prevented when the folding machine cylinder is used. The internal leakage of folding machine cylinder includes the leakage caused by excessive wear of folding machine cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

The folding machine cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the folding machine cylinder should pay attention to: the operation should be as far away from the folding machine cylinder as possible, to avoid falling objects, knocking, rubbing the folding machine cylinder coating. When cleaning the folding machine cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the folding machine cylinder when the oil temperature exceeds 70 ° C.

When the folding machine cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the folding machine cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the folding machine cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the folding machine cylinder can meet the requirements by grinding. However, the life and reliability of this repair folding machine cylinder are not high.

Answers to some questions about folding machine cylinder:

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

What do cylinder internal leakage and external leakage mean?
Internal leakage means that the piston seal in the cylinder is not strict, there is a leak between the two chambers of the cylinder, the oil is still in the cylinder, and the external leakage is that the oil leaks to the outside of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产日韩欧美一区二区乱码| 精品国产免费一区二区久久| 欧美精品在欧美一区二区三区| 日韩码一码二码三码区别| 婷婷激情亚洲综合综合久久| 欧美日本aⅴ一区二区三区| 日韩在线中文字幕观看| 欧美高清手机一区二区| 久久精一区二区三区| 亚洲国产成人久久精品不卡| 日韩一区二区三区在线观看视频| 日韩亚洲一区二区在线| 欧美日韩一区二区三区大片在线观看| 97精品国产综合久久| 国产精品国产三级av| 亚洲区一区二区三区视频| 亚洲人妻最新中文AV| 日韩亚洲欧美综合在线| 欧美日韩一区二区中文字幕| 日韩激情av一区二区| 日韩亚洲中文字幕一区| 日韩欧美亚洲中文字幕区在高我| 日韩无打码一区二区三区| 久久99热精品首页| 日本在线观看黄视频| 成人毛片女人18免费片| 中文字幕久久中文字幕综合网| 欧美日韩一区二区三区大片在线观看| 久久久久久999一区二区三区| 欧美色到久久88综合亚洲精品| 欧美日韩在线免费视频| 精品视频亚洲一区二区三区| 色婷婷久久久久久久久久| 99在线中文字幕一区| 成人午夜日韩看片后入| 日韩一区二区人妻9999| 日本一区二区三区人妻视频| 欧美一区二区亚洲a一区二区| 国产精品不卡在线视频| 欧美一级大片免费观看视频| 国产精品久久久久国产三|