亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Austria

Release time:2023-11-12 15:26:39 Hits: Current position: Home > News

This article mainly introduces:

Austria hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Austria stern plate hydraulic cylinder

(Austria stern plate hydraulic cylinder,produced by Hebei Hengyu company)

stern plate hydraulic cylinder are widely used in Austria,because of simple structure and reliable operation,no transmission clearance,excellent temperature resistance.So our company has designed stern plate hydraulic cylinder for customers from Austria.

Introduction to stern plate hydraulic cylinder:

There are some honeycomb holes in the inner wall of the stern plate hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the stern plate hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the stern plate hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the stern plate hydraulic cylinder is targeted to prevent. Is very necessary.

If the stern plate hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

The quality of the stern plate hydraulic cylinder can not be ignored in the purchase of the stern plate hydraulic cylinder. The stern plate hydraulic cylinder is the main component of the stern plate hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. stern plate hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of stern plate hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

The cavitation of the stern plate hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the stern plate hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Answers to some questions about stern plate hydraulic cylinder:

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美巨屌虐无毛骚逼| 欧美性一区二区三区五区| 西西大尺度无码免费视频| 粉嫩小穴被大鸡巴操视频在线观看| 91精品国产剧情欧美一区二区| 操大美女逼射精视频| 鸡巴插骚逼视频欧美风格| 鸡巴插骚逼视频欧美风格| 国产尤物蜜臀AV| 99视频在线看免费视频| 爆乳喷奶水无码正在播放| 国内揄拍国内精品| 那种视频在线观看你懂的| 日本一区二区在线高清| 日本不卡高清视频在线播放| 国产午夜爽爽爽男女免费动漫AV| 亚洲美女后入在线播放| 午夜福利国产三级片| 亚洲欧美一区二区三区孕妇| 日本中文字幕无人区一区二区| 色男人天堂亚洲男人天堂| 美女人的逼免费观看| 在线无码一区二区三区不卡| 帅哥大鸡巴操美女| 天天摸天天添人人澡| 午夜福利国产三级片| 被公侵犯中文字幕在线观看| 日本 视频 一区二区| 日本成人精品一区二区三区| 中文字幕亚洲欧美精品一区二区| 啊啊啊啊大鸡巴操我视频| 任你橹在线久久精品9| 三级片成人京东热五月天| 妺妺坐在我腿上下面好湿| 无码人妻丰满熟妇区精品| 日韩欧美一级特黄大片欧| 18岁美女破处在线观看| 日韩午夜免费av在线| 最新的精品亚洲一区二区| 美女最骚逼逼视频| 亚洲AV无码一区二区三区天堂古|